 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| this is information on a product in full production. august 2013 docid13587 rev 16 1/105 stm32f103x8 stm32f103xb medium-density performance lin e arm-based 32-bit mcu with 64 or 128 kb flash, usb, can, 7 timers, 2 adcs, 9 com. interfaces datasheet - production data features ? arm 32-bit cortex?-m3 cpu core ? 72 mhz maximum frequency, 1.25 dmips/mhz (dhrystone 2.1) performance at 0 wait state memory access ? single-cycle multiplic ation and hardware division ? memories ? 64 or 128 kbytes of flash memory ? 20 kbytes of sram ? clock, reset and supply management ? 2.0 to 3.6 v application supply and i/os ? por, pdr, and programmable voltage detector (pvd) ? 4-to-16 mhz cr ystal oscillator ? internal 8 mhz factory-trimmed rc ? internal 40 khz rc ? pll for cpu clock ? 32 khz oscillator for rtc with calibration ? low power ? sleep, stop and standby modes ?v bat supply for rtc and backup registers ? 2 x 12-bit, 1 s a/d converters (up to 16 channels) ? conversion range: 0 to 3.6 v ? dual-sample and hold capability ? temperature sensor ? dma ? 7-channel dma controller ? peripherals supported: timers, adc, spis, i 2 cs and usarts ? up to 80 fast i/o ports ? 26/37/51/80 i/os, all mappable on 16 external interrupt vectors and almost all 5 v-tolerant ? debug mode ? serial wire debug (swd) & jtag interfaces ? 7 timers ? three 16-bit timers, each with up to 4 ic/oc/pwm or pulse counter and quadrature (incremental) encoder input ? 16-bit, motor control pwm timer with dead- time generation and emergency stop ? 2 watchdog timers (independent and window) ? systick timer 24-bit downcounter ? up to 9 communication interfaces ? up to 2 x i 2 c interfaces (smbus/pmbus) ? up to 3 usarts (iso 7816 interface, lin, irda capability, modem control) ? up to 2 spis (18 mbit/s) ? can interface (2.0b active) ? usb 2.0 full-speed interface ? crc calculation unit, 96-bit unique id ? packages are ecopack ? table 1. device summary reference part number stm32f103x8 stm32f103c8, stm32f103r8 stm32f103v8, stm32f103t8 stm32f103xb stm32f103rb stm32f103vb, stm32f103cb, stm32f103tb bga100 10 10 mm ufbga100 7 x 7 mm bga64 5 5 mm vfqfpn36 6 6 mm lqfp100 14 14 mm lqfp64 10 10 mm lqfp48 7 7 mm ufqfpn48 7 7 mm www.st.com
contents stm32f103x8, stm32f103xb 2/105 docid13587 rev 16 contents 1 introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.1 device overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.2 full compatibility throughout the family . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.3 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3.1 arm ? cortex?-m3 core with embedded flash and sram . . . . . . . . . 14 2.3.2 embedded flash memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3.3 crc (cyclic redundancy check) calculation unit . . . . . . . . . . . . . . . . . . 14 2.3.4 embedded sram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.3.5 nested vectored interrupt controller (nvic) . . . . . . . . . . . . . . . . . . . . . . 14 2.3.6 external interrupt/event controller (exti) . . . . . . . . . . . . . . . . . . . . . . . 15 2.3.7 clocks and startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.3.8 boot modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.3.9 power supply schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.3.10 power supply supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2.3.11 voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.3.12 low-power modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2.3.13 dma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.3.14 rtc (real-time clock) and backup register s . . . . . . . . . . . . . . . . . . . . . . 17 2.3.15 timers and watchdogs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.3.16 i2c bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.3.17 universal synchronous/asynchronous receiver transmitter (usart) . . 19 2.3.18 serial peripheral interface (spi) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.3.19 controller area network (can) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.3.20 universal serial bus (usb) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2.3.21 gpios (general-purpose inputs/outputs) . . . . . . . . . . . . . . . . . . . . . . . . 20 2.3.22 adc (analog-to-digital converter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.3.23 temperature sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 2.3.24 serial wire jtag debug port (swj-dp) . . . . . . . . . . . . . . . . . . . . . . . . . 20 3 pinouts and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 4 memory mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 docid13587 rev 16 3/105 stm32f103x8, stm32f103xb contents 4 5 electrical characteristi cs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1 parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.1 minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.2 typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.3 typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.4 loading capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.5 pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 5.1.6 power supply scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 5.1.7 current consumption measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.2 absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 5.3 operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 5.3.1 general operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 5.3.2 operating conditions at power-up / powe r-down . . . . . . . . . . . . . . . . . . 39 5.3.3 embedded reset and power control bloc k characteristics . . . . . . . . . . . 40 5.3.4 embedded reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.3.5 supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 5.3.6 external clock source characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 5.3.7 internal clock source charac teristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 5.3.8 pll characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 5.3.9 memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 5.3.10 emc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 5.3.11 absolute maximum ratings (electrical sensitivity) . . . . . . . . . . . . . . . . . 60 5.3.12 i/o current injection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 5.3.13 i/o port characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 5.3.14 nrst pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 5.3.15 tim timer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 5.3.16 communications interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 5.3.17 can (controller area network) interface . . . . . . . . . . . . . . . . . . . . . . . . 75 5.3.18 12-bit adc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 5.3.19 temperature sensor characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 6 package characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6.1 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 6.2 thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 6.2.1 reference document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 6.2.2 selecting the product temperature range . . . . . . . . . . . . . . . . . . . . . . . 94 contents stm32f103x8, stm32f103xb 4/105 docid13587 rev 16 7 ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 8 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 docid13587 rev 16 5/105 stm32f103x8, stm32f103xb list of tables 6 list of tables table 1. device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 table 2. stm32f103xx medium-density device features and peripheral counts . . . . . . . . . . . . . . . 10 table 3. stm32f103xx family . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 4. timer feature comparison . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 5. medium-density stm32f103xx pin definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 table 6. voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 table 7. current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 8. thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 9. general operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 table 10. operating conditions at power-up / power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 table 11. embedded reset and power control block characterist ics. . . . . . . . . . . . . . . . . . . . . . . . . . 40 table 12. embedded internal reference voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1 table 13. maximum current consumption in run mode, code with data processing running from flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 table 14. maximum current consumption in run mode, code with data processing running from ram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 table 15. maximum current consumption in sleep mode, code running from flash or ram. . . . . . . 44 table 16. typical and maximum current consumptions in stop and standby modes . . . . . . . . . . . . 45 table 17. typical current consumption in run mode, code with data processing running from flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 table 18. typical current consumption in sleep mode, code running from flash or ram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 table 19. peripheral current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 table 20. high-speed external user clock characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 21. low-speed external user clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 table 22. hse 4-16 mhz oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 table 23. lse oscillator characteristics (f lse = 32.768 khz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 table 24. hsi oscillator characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 table 25. lsi oscillator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 table 26. low-power mode wakeup timings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 table 27. pll characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 table 28. flash memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 table 29. flash memory endurance and data retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 table 30. ems characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 table 31. emi characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 table 32. esd absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 table 33. electrical sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 table 34. i/o current injection susceptibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 table 35. i/o static characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 table 36. output voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 table 37. i/o ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 table 38. nrst pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 table 39. timx characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 table 40. i 2 c characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 table 41. scl frequency (f pclk1 = 36 mhz.,v dd_i2c = 3.3 v) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 table 42. spi characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 table 43. usb startup time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 table 44. usb dc electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 list of tables stm32f103x8, stm32f103xb 6/105 docid13587 rev 16 table 45. usb: full-speed electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 table 46. adc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 table 47. r ain max for f adc = 14 mhz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 table 48. adc accuracy - limited test conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 table 49. adc accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 table 50. ts characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 table 51. vfqfpn36 6 x 6 mm, 0.5 mm pitch, package mechanical data . . . . . . . . . . . . . . . . . . . . 82 table 52. ufqfpn48 7 x 7 mm, 0.5 mm pitch, package mech anical data . . . . . . . . . . . . . . . . . . . . 83 table 53. lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 table 54. lqpf100, 14 x 14 mm 100-pin low-profile quad flat package mechanical data. . . . . . . . . 87 table 55. ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 table 56. lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package mechanical data . . . . . . . . . . 89 table 57. tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package mechanical data. . . 90 table 58. lqfp48, 7 x 7 mm, 48-pin low-profile quad flat package mechanical data . . . . . . . . . . . . 92 table 59. package thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 table 60. ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 table 61. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 docid13587 rev 16 7/105 stm32f103x8, stm32f103xb list of figures 8 list of figures figure 1. stm32f103xx performance line block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 figure 2. clock tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 figure 3. stm32f103xx performance line lfbga100 ballout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 figure 4. stm32f103xx performance line lqfp100 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 figure 5. stm32f103xx performance line ufbga100 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 figure 6. stm32f103xx performance line lqfp64 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 figure 7. stm32f103xx performance line tfbga64 ballout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 figure 8. stm32f103xx performance line lqfp48 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 figure 9. stm32f103xx performance line ufqfpn48 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 figure 10. stm32f103xx performance line vfqfpn36 pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 figure 11. memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 figure 12. pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 figure 13. pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 figure 14. power supply scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 figure 15. current consumption measurement scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 figure 16. typical current consumption in run mode versus frequency (at 3.6 v) - code with data processing running from ram, perip herals enabled. . . . . . . . . . . . . . . . . . 43 figure 17. typical current consumption in run mode versus frequency (at 3.6 v) - code with data processing running from ram, perip herals disabled . . . . . . . . . . . . . . . . . 43 figure 18. typical current consumption on v bat with rtc on versus temperature at different v bat values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 figure 19. typical current consumption in stop mode with regulator in run mode versus temperature at v dd = 3.3 v and 3.6 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 figure 20. typical current consumption in stop mode with regulator in low-power mode versus temperature at v dd = 3.3 v and 3.6 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 figure 21. typical current consumption in standby mode versus temperature at v dd = 3.3 v and 3.6 v . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 figure 22. high-speed external clock source ac timing diagra m . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 figure 23. low-speed external clock source ac timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 figure 24. typical application with an 8 mhz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 figure 25. typical application with a 32.768 khz crystal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 figure 26. standard i/o input characterist ics - cmos port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 figure 27. standard i/o input characteristics - ttl port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 figure 28. 5 v tolerant i/o inpu t characteristics - cmos port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 figure 29. 5 v tolerant i/o input characteristics - ttl port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 figure 30. i/o ac characteristics definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 figure 31. recommended nrst pin protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 figure 32. i 2 c bus ac waveforms and measurement ci rcuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 figure 33. spi timing diagram - slave mode and cpha = 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 figure 34. spi timing diagram - slave mode and cpha = 1 (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 figure 35. spi timing diagram - master mode (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 figure 36. usb timings: definition of data signal rise and fa ll time . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 figure 37. adc accuracy characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 figure 38. typical connection diagram using the adc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 figure 39. power supply and reference decoupling (v ref+ not connected to v dda ). . . . . . . . . . . . . . 79 figure 40. power supply and reference decoupling (v ref+ connected to v dda ). . . . . . . . . . . . . . . . . 80 figure 41. vfqfpn36 6 x 6 mm, 0.5 mm pitch, package outline (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 figure 42. vfqfpn36 recommended footprint (dimensions in mm) (1)(2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 list of figures stm32f103x8, stm32f103xb 8/105 docid13587 rev 16 figure 43. ufqfpn48 7 x 7 mm, 0.5 mm pitch, package outli ne . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 figure 44. ufqfpn48 recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 figure 45. lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 figure 46. recommended pcb design rules (0.80/0.75 mm pi tch bga) . . . . . . . . . . . . . . . . . . . . . . 86 figure 47. lqfp100, 14 x 14 mm 100-pin low-profile quad flat package outline . . . . . . . . . . . . . . . . 87 figure 48. lqfp100 recommended footprint (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 figure 49. ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 figure 50. lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package outline . . . . . . . . . . . . . . . . . . 89 figure 51. lqfp64 recommended footprint (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 figure 52. tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package outline . . . . . . . . . . 90 figure 53. recommended pcb design rules for pads (0.5 mm pitch bga) . . . . . . . . . . . . . . . . . . . . 91 figure 54. lqfp48, 7 x 7 mm, 48-pin low-profile quad flat package outline . . . . . . . . . . . . . . . . . . . . 92 figure 55. lqfp48 recommended footprint (1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 figure 56. lqfp100 p d max vs. t a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 docid13587 rev 16 9/105 stm32f103x8, stm32f103xb introduction 104 1 introduction this datasheet provides the ordering informat ion and mechanical devic e characteristics of the stm32f103x8 and stm32f103xb medium-density performance line microcontrollers. for more details on the whole stmicroelectronics stm32f103xx family, please refer to section 2.2: full compatibilit y throughout the family . the medium-density stm32f103xx datasheet should be read in conjunction with the low-, medium- and high-density stm32f10xxx reference manual . the reference and flash programming manuals are both available from the stmicroelectronics website www.st.com. for information on the cortex?-m3 core please refer to the cortex?-m3 technical reference manual, available from the www. arm.com website at the following address: http://infocenter.arm.com/help/inde x.jsp?topic=/com.arm.doc.ddi0337e/. 2 description the stm32f103xx medium-density performance line family incorporates the high- performance arm cortex?-m3 32-bit risc co re operating at a 72 mhz frequency, high- speed embedded memories (flash memory up to 128 kbytes and sram up to 20 kbytes), and an extensive ra nge of enhanced i/ os and peripherals connec ted to two apb buses. all devices offer two 12-bit adcs, three general pu rpose 16-bit timers plus one pwm timer, as well as standard and advanced communication interfaces: up to two i 2 cs and spis, three usarts, an usb and a can. the devices operate from a 2.0 to 3.6 v power su pply. they are available in both the ?40 to +85 c temperature range and the ?40 to +105 c extended temperature range. a comprehensive set of power-saving mode allo ws the design of low-power applications. the stm32f103xx medium-density performance lin e family includes devices in six different package types: from 36 pins to 100 pins. depending on the device chosen, different sets of peripherals are included, the description below gives an overview of the complete range of peripherals proposed in this family. these features make the stm32f103xx medium -density performance line microcontroller family suitable for a wid e range of applications such as motor drives, application control, medical and handheld equipment, pc and gami ng peripherals, gps platforms, industrial applications, plcs, inve rters, printers, scanners, alarm systems, video intercoms, and hvacs. description stm32f103x8, stm32f103xb 10/105 docid13587 rev 16 2.1 device overview table 2. stm32f103xx medium-density device features and peripheral counts peripheral stm32f103tx stm32f103cx stm32f103rx stm32f103vx flash - kbytes 64 128 64 128 64 128 64 128 sram - kbytes 20 20 20 20 timers general-purpose 33 3 3 advanced-control 11 1 1 communication spi 12 2 2 i 2 c 12 2 2 usart 23 3 3 usb 11 1 1 can 11 1 1 gpios 26 37 51 80 12-bit synchronized adc number of channels 2 10 channels 2 10 channels 2 16 channels (1) 1. on the tfbga64 package only 15 channels are av ailable (one analog input pin has been replaced by ?vref+?). 2 16 channels cpu frequency 72 mhz operating voltage 2.0 to 3.6 v operating temperatures ambient temperatures: -40 to +85 c / -40 to +105 c (see table 9 ) junction temperature: -40 to + 125 c (see table 9 ) packages vfqfpn36 lqfp48, ufqfpn48 lqfp64, tfbga64 lqfp100, lfbga100, ufbga100 docid13587 rev 16 11/105 stm32f103x8, stm32f103xb description 104 figure 1. stm32f103xx performance line block diagram 1. t a = ?40 c to +105 c (junction temperature up to 125 c). 2. af = alternate function on i/o port pin. usbdp/can_tx pa[ 15:0] exti wwdg 12bit adc1 16af jtdi jtck/swclk jtms/swdio njtrst trst jtdo nrst v dd = 2 to 3 .6v 8 0af pb[ 15:0] pc[15:0] ahb2 mosi,miso,sck,nss sram 2x( 8 x16bit) wakeup gpioa gpiob gpioc f max : 72 m hz v ss scl,sda i2c2 v ref+ gp dma tim2 tim 3 xtal osc 4-16 mhz xtal 3 2 khz osc_in osc_out osc 3 2_out osc 3 2_in pll & apb1 : f max =24 / 3 6 mhz pclk1 hclk clock managt pclk2 as af as af flash 12 8 kb volt. reg. 3 . 3 v to 1. 8 v power backu p i nterf ace as af tim 4 busm atrix 64 bit inte rfac e 20 kb rtc rc 8 mhz cortex-m 3 cpu ibu s dbus pbu s obl flash sram 512b trace controlle r usart1 usart2 spi2 bx can 7 ch annels back up reg 4 chann els tim1 3 co mpl. chann els scl,sda,smba i2c1 as af rx,tx, cts, rts, usart 3 temp sensor v ref- pd[15:0] gpiod pe[15:0] gpioe ahb:f max =4 8 /72 mhz etr and bkin 4 chann els 4 chann els 4 chann els fclk rc 40 khz stand by iwdg @vbat por / pdr supply @vdda vdda vssa @vdda v bat rx,tx, cts, rts, smart card as af rx,tx, cts, rts, ck, smartcard as af apb2 : f max =4 8 / 72 mhz nvic spi1 mosi,miso, sck,nss as af 12bi t adc2 if if if interface @vdda supervision pvd rst int @vdd ahb2 apb2 apb 1 awu tamper-rtc @vdd usb 2.0 fs usbdm/can_rx syst em ai14 3 90d traceclk traced[0: 3 ] as as sw/jtag tpiu trace/trig ck, smartcard as af description stm32f103x8, stm32f103xb 12/105 docid13587 rev 16 figure 2. clock tree 1. when the hsi is used as a pll clock input, the maxi mum system clock frequency t hat can be achieved is 64 mhz. 2. for the usb function to be available, both hse and pll must be enabled, with usbclk running at 48 mhz. 3. to have an adc conversion time of 1 s, apb2 must be at 14 mhz, 28 mhz or 56 mhz. h s e o s c 4-16 mhz o s c_in o s c_out o s c32_in o s c32_out l s e o s c 32.768 khz h s i rc 8 mhz l s i rc 40 khz to independent w a tchdog (iwdg) pll x2, x3, x4 pllmul legend: mco clock o u tp u t m a in pllxtpre /2 ..., x16 ahb pre s c a ler /1, 2..512 /2 pllclk h s i h s e apb1 pre s c a ler /1, 2, 4, 8, 16 adc pre s c a ler /2, 4, 6, 8 adcclk pclk1 hclk pllclk to ahb bus , core, memory a nd dma u s bclk to u s b interf a ce to tim2, 3 a nd 4 u s b pre s c a ler /1, 1.5 to adc l s e l s i h s i /128 /2 h s i h s e peripher a l s to apb1 peripher a l clock en ab le (13 b it s ) en ab le (3 b it s ) p eripher a l clock apb2 pre s c a ler /1, 2, 4, 8, 16 pclk2 to tim1 peripher a l s to apb2 peripher a l clock en ab le (11 b it s ) en ab le (1 b it) peripher a l clock 48 mhz 72 mhz m a x 72 mhz 72 mhz m a x 36 mhz m a x to rtc pll s rc s w mco c ss to cortex s y s tem timer /8 clock en ab le (3 b it s ) s y s clk m a x rtcclk rtc s el[1:0] tim1clk timxclk iwdgclk s y s clk fclk cortex free r u nning clock tim2,3, 4 if (apb1 pre s c a ler =1) x1 el s e x2 tim1 timer if (apb2 pre s c a ler =1) x1 el s e x2 h s e = high- s peed extern a l clock s ign a l h s i = high- s peed intern a l clock s ign a l l s i = low- s peed intern a l clock s ign a l l s e = low- s peed extern a l clock s ign a l a i14903 flitfclk to fl as h progr a mming interf a ce docid13587 rev 16 13/105 stm32f103x8, stm32f103xb description 104 2.2 full compatibility throughout the family the stm32f103xx is a complete family whose members are fully pin-to-pin, software and feature compatible. in the reference manual, the stm32f103x4 and stm32f103x6 are identified as low-density devices, the stm32f 103x8 and stm32f103xb are referred to as medium-density devices, and the stm32f 103xc, stm32f103xd and stm32f103xe are referred to as high-density devices. low- and high-density devices are an extens ion of the stm32f103x8/b devices, they are specified in the stm32f103x4/6 and stm32f 103xc/d/e datasheets, respectively. low- density devices feature lower flash memory and ram capacities, less timers and peripherals. high-density devices have highe r flash memory and ram capacities, and additional peripherals like sdio, fsmc, i 2 s and dac, while remainin g fully compatible with the other members of the stm32f103xx family. the stm32f103x4, stm32f103x6, stm32f103xc, stm32f103xd and stm32f103xe are a drop-in replacement for stm32f103x8/b medium-density devices, allowing the user to try different memory densities and prov iding a greater degree of freedom during the development cycle. moreover, the stm32f103xx performance line fa mily is fully compatible with all existing stm32f101xx access line and stm32f102xx usb access line devices. table 3. stm32f103xx family pinout low-density devices medium-densi ty devices high-density devices 16 kb flash 32 kb flash (1) 1. for orderable part numbers that do not show the a internal code after the temperature range code (6 or 7), the reference datasheet for electr ical characteristics is that of the stm32f103x8/b medium-density devices. 64 kb flash 128 kb flash 256 kb flash 384 kb flash 512 kb flash 6 kb ram 10 kb ram 20 kb ram 20 kb ram 48 kb ram 64 kb ram 64 kb ram 144 5 usarts 4 16-bit timers, 2 basic timers 3 spis, 2 i 2 ss, 2 i2cs usb, can, 2 pwm timers 3 adcs, 2 dacs, 1 sdio fsmc (100 and 144 pins) 100 3 usarts 3 16-bit timers 2 spis, 2 i 2 cs, usb, can, 1 pwm timer 2 adcs 64 2 usarts 2 16-bit timers 1 spi, 1 i 2 c, usb, can, 1 pwm timer 2 adcs 48 36 description stm32f103x8, stm32f103xb 14/105 docid13587 rev 16 2.3 overview 2.3.1 arm ? cortex?-m3 core with embedded flash and sram the arm cortex?-m3 processor is the latest generation of arm processors for embedded systems. it has been developed to provide a low-cost platform that meets the needs of mcu implementation, with a reduced pin count and low-power consumption, while delivering outstanding computational performance and an advanced system response to interrupts. the arm cortex?-m3 32-bit risc processor features exceptional code-efficiency, delivering the high-performance expected from an arm core in the memory size usually associated with 8- and 16-bit devices. the stm32f103xx performance line family having an embedded arm core, is therefore compatible with all arm tools and software. figure 1 shows the general block diagram of the device family. 2.3.2 embedded flash memory 64 or 128 kbytes of embedded flash is available for storing programs and data. 2.3.3 crc (cyclic redundan cy check) calculation unit the crc (cyclic redundancy check) calculation unit is used to get a crc code from a 32-bit data word and a fixed generator polynomial. among other applications, crc-based techniques are used to verify data transmission or storage integrity. in the scope of the en/iec 60335-1 standard, they offer a means of verifying the flash memory integrity. the crc calculation unit helps compute a signature of the software during runtime, to be compared with a reference signature generated at link- time and stored at a given memory location. 2.3.4 embedded sram twenty kbytes of embedded sram accessed (read/write) at cpu clock speed with 0 wait states. 2.3.5 nested vectored interrupt controller (nvic) the stm32f103xx performance line embeds a ne sted vectored interrupt controller able to handle up to 43 maskable interrupt channels (not including the 16 interrupt lines of cortex?-m3) and 16 priority levels. ? closely coupled nvic gives low-latency interrupt processing ? interrupt entry vector table address passed directly to the core ? closely coupled nvic core interface ? allows early processing of interrupts ? processing of late arriving higher priority interrupts ? support for tail-chaining ? processor state automatically saved ? interrupt entry restored on interrupt exit with no instruction overhead docid13587 rev 16 15/105 stm32f103x8, stm32f103xb description 104 this hardware block provides flexible interrupt management features with minimal interrupt latency. 2.3.6 external interrupt /event controller (exti) the external interrupt/event controller consists of 19 edge detector lines used to generate interrupt/event requests. each line can be independently configured to select the trigger event (rising edge, falling edge, both) and can be masked independently. a pending register maintains the status of the interrupt requests. the exti can detect an external line with a pulse width shorter than the in ternal apb2 clock period. up to 80 gpios can be connected to the 16 external interrupt lines. 2.3.7 clocks and startup system clock selection is perf ormed on startup, however the internal rc 8 mhz oscillator is selected as default cpu clock on reset. an external 4-16 mhz clock can be selected, in which case it is monitored for fa ilure. if failure is detected, th e system automatically switches back to the internal rc oscillator. a software interrupt is genera ted if enabled. similarly, full interrupt management of the pll clock entry is available when necessary (for example on failure of an indirectly used extern al crystal, resona tor or oscillator). several prescalers allow t he configuration of the ahb frequency, the high-speed apb (apb2) and the low-sp eed apb (apb1) domains. the maxi mum frequency of the ahb and the high-speed apb domains is 72 mhz. the maximum allowed frequency of the low-speed apb domain is 36 mhz. see figure 2 for details on the clock tree. 2.3.8 boot modes at startup, boot pins are used to select one of three boot options: ? boot from user flash ? boot from system memory ? boot from embedded sram the boot loader is located in system memory. it is used to reprogram the flash memory by using usart1. for further details please refer to an2606. 2.3.9 power supply schemes ? v dd = 2.0 to 3.6 v: external power supply for i/os and the internal regulator. provided externally through v dd pins. ? v ssa , v dda = 2.0 to 3.6 v: external analog po wer supplies for adc, reset blocks, rcs and pll (minimum voltage to be applied to v dda is 2.4 v when the adc is used). v dda and v ssa must be connected to v dd and v ss , respectively. ? v bat = 1.8 to 3.6 v: power supply for rtc, external clock 32 khz oscillator and backup registers (through power switch) when v dd is not present. for more details on how to connect power pins, refer to figure 14: power supply scheme . 2.3.10 power supply supervisor the device has an integrated power-on reset (por)/power-down reset (pdr) circuitry. it is always active, and ensures proper operation starting from/down to 2 v. the device remains description stm32f103x8, stm32f103xb 16/105 docid13587 rev 16 in reset mode when v dd is below a specified threshold, v por/pdr , without the need for an external reset circuit. the device features an embedded programmable voltage detector (pvd) that monitors the v dd /v dda power supply and compares it to the v pvd threshold. an interrupt can be generated when v dd /v dda drops below the v pvd threshold and/or when v dd /v dda is higher than the v pvd threshold. the interrupt service routine can then generate a warning message and/or put the mcu into a safe state. the pvd is enabled by software. refer to table 11: embedded reset and power control block characteristics for the values of v por/pdr and v pvd . 2.3.11 voltage regulator the regulator has three operation modes: main (mr), low power (lpr) and power down. ? mr is used in the nominal regulation mode (run) ? lpr is used in the stop mode ? power down is used in standby mode: the re gulator output is in high impedance: the kernel circuitry is powered do wn, inducing zero consumption (but the contents of the registers and sram are lost) this regulator is always enabled after reset. it is disabled in standby mode, providing high impedance output. 2.3.12 low-power modes the stm32f103xx performance line supports three low-power modes to achieve the best compromise between low power consumption, short startup time and available wakeup sources: ? sleep mode in sleep mode, only the cpu is stopped. all peripherals continue to operate and can wake up the cpu when an interrupt/event occurs. ? stop mode the stop mode achieves the lowest power consumption while retaining the content of sram and registers. all clocks in the 1.8 v domain are stopped, the pll, the hsi rc and the hse crystal oscillators are disabled . the voltage regulator can also be put either in normal or in low power mode. the device can be woken up from stop mode by any of the exti line. the exti line source can be one of the 16 external lines, the pvd output, the rtc alarm or the usb wakeup. ? standby mode the standby mode is used to achieve the lowest power consumption. the internal voltage regulator is switched off so that the entire 1.8 v domain is powered off. the pll, the hsi rc and the hse crystal oscillato rs are also switched off. after entering standby mode, sram and register contents are lost except for registers in the backup domain and standby circuitry. the device exits standby mode when an external reset (nrst pin), an iwdg reset, a rising edge on the wkup pin, or an rtc alarm occurs. note: the rtc, the iwdg, and the corresponding clock sources are not stopped by entering stop or standby mode. docid13587 rev 16 17/105 stm32f103x8, stm32f103xb description 104 2.3.13 dma the flexible 7-channel general-purpose dma is able to manage memory-to-memory, peripheral-to-memory and memory-to-peripheral transfers. the dma controller supports circular buffer management avoiding the ge neration of interrupts when the controller reaches the end of the buffer. each channel is connected to dedicated hardw are dma requests, with support for software trigger on each channel. configuration is made by software and transfer sizes between source and destination are independent. the dma can be used with the main peripherals: spi, i 2 c, usart, general-purpose and advanced-control timers timx and adc. 2.3.14 rtc (real-time cl ock) and backup registers the rtc and the backup registers are supplied through a switch that takes power either on v dd supply when present or through the v bat pin. the backup registers are ten 16-bit registers used to store 20 bytes of user application data when v dd power is not present. the real-time clock provides a set of continuously running counters which can be used with suitable software to provide a clock calendar function, and provides an alarm interrupt and a periodic interrupt. it is clocked by a 32.768 khz external crystal, resonator or oscillator, the internal low-power rc oscillato r or the high-speed external clock di vided by 128. the internal low-power rc has a typical frequency of 40 khz. the rtc can be calibrated using an external 512 hz output to compensate for any natural crystal deviation. the rtc features a 32-bit programmable counter for long-term measurement using the compare register to generate an alarm. a 20-bit pres caler is used for the time base clock and is by default configured to generate a time base of 1 second from a clock at 32.768 khz. 2.3.15 timers and watchdogs the medium-density stm32f103xx performance line devices include an advanced-control timer, three general-purpose timers, two watchdog timers and a systick timer. table 4 compares the features of the advanced-control and general-purpose timers. table 4. timer feature comparison timer counter resolution counter type prescaler factor dma request generation capture/compare channels complementary outputs tim1 16-bit up, down, up/down any integer between 1 and 65536 yes 4 yes tim2, tim3, tim4 16-bit up, down, up/down any integer between 1 and 65536 yes 4 no description stm32f103x8, stm32f103xb 18/105 docid13587 rev 16 advanced-control timer (tim1) the advanced-control timer (tim1) can be seen as a three-phase pwm multiplexed on 6 channels. it has complementary pwm outputs with programmable inserted dead-times. it can also be seen as a complete general-purpose timer. the 4 independent channels can be used for ? input capture ? output compare ? pwm generation (edge- or center-aligned modes) ? one-pulse mode output if configured as a general-purpose 16-bit timer, it has the same features as the timx timer. if configured as the 16-bit pw m generator, it has full modu lation capability (0-100%). in debug mode, the advanced-control timer counter can be frozen and the pwm outputs disabled to turn off any power switch driven by these outputs. many features are shared with those of the general-purpose tim timers which have the same architecture. the advanced-control timer can therefore work together with the tim timers via the timer link feature fo r synchronization or event chaining. general-purpose timers (timx) there are up to three synchronizable general-purpose timers embedded in the stm32f103xx performance line devices. these timers are based on a 16-bit auto-reload up/down counter, a 16-bit prescaler and f eature 4 independent channels each for input capture/output compare, pwm or one-pulse mode output. this gives up to 12 input captures/output compares/pwms on the largest packages. the general-purpose timers can work together with the advanced-control timer via the timer link feature for synchronization or event chaining. their counter can be frozen in debug mode. any of the general-purpose timers can be used to generate pwm outputs. they all have independent dma request generation. these timers are capable of handling quadrat ure (incremental) encoder signals and the digital outputs from 1 to 3 hall-effect sensors. independent watchdog the independent watchdog is based on a 12-bit downcounter and 8-bit prescaler. it is clocked from an independent 40 khz internal rc and as it operates independently of the main clock, it can operate in stop and stan dby modes. it can be used either as a watchdog to reset the device when a problem occurs, or as a free-running timer for application timeout management. it is hardware- or software-configurable through the option bytes. the counter can be frozen in debug mode. window watchdog the window watchdog is based on a 7-bit downcounter that can be set as free-running. it can be used as a watchdog to reset the device when a problem occurs. it is clocked from the main clock. it has an early warning interrupt capab ility and the counter can be frozen in debug mode. docid13587 rev 16 19/105 stm32f103x8, stm32f103xb description 104 systick timer this timer is dedicated for os, but could also be used as a standard downcounter. it features: ? a 24-bit downcounter ? autoreload capability ? maskable system interrupt generation when the counter reaches 0 ? programmable clock source 2.3.16 i2c bus up to two i2c bus interfaces can operate in multimaster and slave mo des. they can support standard and fast modes. they support dual slave addressing (7-bit onl y) and both 7/10-bit addressing in master mode. a hardware crc generation/verification is embedded. they can be served by dma and they support sm bus 2.0/pm bus. 2.3.17 universal sync hronous/asynchronous receiver transmitter (usart) one of the usart interfaces is able to commu nicate at speeds of up to 4.5 mbit/s. the other available interfaces communicate at up to 2.25 mbit/s. they provide hardware management of the cts and rts signals, irda sir endec support, are iso 7816 compliant and have lin master/slave capability. all usart interfaces can be served by the dma controller. 2.3.18 serial peripheral interface (spi) up to two spis are able to communicate up to 18 mbits/s in slave and master modes in full- duplex and simplex communication modes. the 3-bit prescaler gives 8 master mode frequencies and the frame is configurable to 8 bits or 16 bits. the hardware crc generation/verification support s basic sd card/mmc modes. both spis can be served by the dma controller. 2.3.19 controller area network (can) the can is compliant with specif ications 2.0a and b (active) wit h a bit rate up to 1 mbit/s. it can receive and transmit standard frames with 11-bit identifiers as well as extended frames with 29-bit identifiers. it has three transmit mailboxes, two receive fifos with 3 stages and 14 scalable filter banks. 2.3.20 universal serial bus (usb) the stm32f103xx performance line embeds a usb device peripheral compatible with the usb full-speed 12 mbs. the usb interface im plements a full-speed (12 mbit/s) function interface. it has software-configurable endpo int setting and suspend/resume support. the dedicated 48 mhz clock is generated from the in ternal main pll (the clock source must use a hse crystal oscillator). description stm32f103x8, stm32f103xb 20/105 docid13587 rev 16 2.3.21 gpios (general- purpose inputs/outputs) each of the gpio pins can be configured by so ftware as output (push-pull or open-drain), as input (with or without pull-up or pull-down) or as peripheral alternate function. most of the gpio pins are shared with digital or analog alternate functions. all gpios are high current- capable. the i/os alternate function configuration c an be locked if needed following a specific sequence in order to avoid spurious writing to the i/os registers. i/os on apb2 with up to 18 mhz toggling speed. 2.3.22 adc (analog-to-digital converter) two 12-bit analog-to-digital converters are embedded into stm32f103xx performance line devices and each adc shares up to 16 external channels, performing conversions in single- shot or scan modes. in scan mode, automatic conversion is performed on a selected group of analog inputs. additional logic functions embedded in the adc interface allow: ? simultaneous sample and hold ? interleaved sample and hold ? single shunt the adc can be served by the dma controller. an analog watchdog feature allows very precis e monitoring of the converted voltage of one, some or all selected channels. an interrupt is generated when the converted voltage is outside the programmed thresholds. the events generated by the general-purpose ti mers (timx) and the advanced-control timer (tim1) can be internally connected to the adc start trigger, injection trigger, and dma trigger respectively, to allow the applicatio n to synchronize a/d conversion and timers. 2.3.23 temperature sensor the temperature sensor has to generate a voltage that varies linearly with temperature. the conversion range is between 2 v < v dda < 3.6 v. the temperature sensor is internally connected to the adc12_in16 input channel which is used to convert the sensor output voltage into a digital value. 2.3.24 serial wire jtag debug port (swj-dp) the arm swj-dp interface is embedded. and is a combined jtag and serial wire debug port that enables either a serial wire debug or a jtag probe to be connected to the target. the jtag tms and tck pins are shared wit h swdio and swclk, respectively, and a specific sequence on the tms pin is us ed to switch between jtag-dp and sw-dp. docid13587 rev 16 21/105 stm32f103x8, stm32f103xb pinouts and pin description 104 3 pinouts and pin description figure 3. stm32f103xx performance line lfbga100 ballout ai16001c pe10 pc14- o s c32_in pc5 pa5 pc3 pb4 pe15 pb2 pc4 pa4 h pe14 pe11 pe7 d pd4 pd3 pb8 pe3 c pd0 pc12 pe5 pb5 pc0 pe2 b pc11 pd2 pc15- o s c32_out pb7 pb6 a 8 7 6 5 4 3 2 1 v ss _5 o s c_in o s c_out v dd_5 g f e pc1 v ref? pc13- tamper-rtc pb9 pa15 pb3 pe4 pe1 pe0 v ss _1 pd1 pe6 nr s t pc2 v ss _3 v ss _4 nc v dd_3 v dd_4 pb15 v bat pd5 pd6 boot0 pd7 v ss _2 v ss a pa1 v dd_2 v dd_1 pb14 pa0-wkup 10 9 k j pd10 pd11 pa8 pa9 pa10 pa11 pa12 pc10 pa13 pa14 pc9 pc7 pc6 pd15 pc8 pd14 pe12 pb1 pa7 pb11 pe8 pb0 pa6 pb10 pe13 pe9 v dda pb13 v ref+ pa3 pb12 pa2 pd8 pd9 pd13 pd12 pinouts and pin description stm32f103x8, stm32f103xb 22/105 docid13587 rev 16 figure 4. stm32f103xx performance line lqfp100 pinout 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 vdd_2 v ss _2 nc pa 1 3 pa 1 2 pa 1 1 pa 1 0 pa 9 pa 8 pc9 pc8 pc7 pc6 pd15 pd14 pd13 pd12 pd11 pd10 pd9 pd8 pb15 pb14 pb13 pb12 pa 3 v ss _4 vdd_4 pa 4 pa 5 pa 6 pa 7 pc4 pc5 pb0 pb1 pb2 pe7 pe8 pe9 pe10 pe11 pe12 pe13 pe14 pe15 pb10 pb11 v ss _1 vdd_1 vdd_3 v ss _3 pe1 pe0 pb9 pb8 boot0 pb7 pb6 pb5 pb4 pb3 pd7 pd6 pd5 pd4 pd3 pd2 pd1 pd0 pc12 pc11 pc10 pa15 pa14 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 pe2 pe3 pe4 pe5 pe6 vbat pc13-tamper-rtc pc14-o s c32_in pc15-o s c32_out v ss _5 vdd_5 o s c_in o s c_out nr s t pc0 pc1 pc2 pc3 v ss a vref- vref+ vdda pa 0 - w k u p pa 1 pa 2 a i14391 lqfp100 docid13587 rev 16 23/105 stm32f103x8, stm32f103xb pinouts and pin description 104 figure 5. stm32f103xx performance line ufbga100 pinout ms30481v1 a b e d c f g h j k l m pe3 osc_in pc15 osc32_out pc14 rtc_tamper pe4 osc_out pc0 vssa vref- vref+ vdda pe1 pe5 pe2 pe6 vbat vss_5 vdd_5 nrst pc1 pc3 pa0 wkup1 pa1 pb8 pe0 pb9 vss_3 vss_4 vdd_4 pc2 pa2 pa3 pa4 boot0 pb7 vdd_3 pa5 pa6 pa7 pd7 pb6 pb5 pc4 pc5 pb0 pd5 pd6 pb2 pb1 pb4 pd4 pe8 pe7 pb3 pd3 pd2 pd9 pe10 pe9 pa15 pd1 pd0 pd8 pe12 pe11 pa14 pc12 pc11 pc8 pa9 pd15 pd12 pb15 pb10 pe13 pa13 pc10 nc pa8 pc7 pd14 pd11 pb14 pb11 pe14 vss_2 vdd_2 pa12 pa11 pa10 pc9 pc6 pd13 pd10 pb13 pb12 pe15 vss_1 vdd_1 pc13 osc32_in pinouts and pin description stm32f103x8, stm32f103xb 24/105 docid13587 rev 16 figure 6. stm32f103xx performance line lqfp64 pinout 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 17 18 19 20 21 22 23 24 29 30 31 32 25 26 27 28 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 vbat pc13-tamper-rtc pc14-o s c32_in pc15-o s c32_out pd0 o s c_in pd1 o s c_out nr s t pc0 pc1 pc2 pc3 v ss a vdda pa 0 - w k u p pa 1 pa 2 vdd_3 v ss _3 pb9 pb8 boot0 pb7 pb6 pb5 pb4 pb3 pd2 pc12 pc11 pc10 pa 1 5 pa 1 4 vdd_2 v ss _2 pa 1 3 pa 1 2 pa 1 1 pa 1 0 pa 9 pa 8 pc9 pc8 pc7 pc6 pb15 pb14 pb13 pb12 pa 3 v ss _4 vdd_4 pa 4 pa 5 pa 6 pa 7 pc4 pc5 pb0 pb1 pb2 pb10 pb11 v ss _1 vdd_1 lqfp64 a i14392 docid13587 rev 16 25/105 stm32f103x8, stm32f103xb pinouts and pin description 104 figure 7. stm32f103xx performance line tfbga64 ballout ai15494 pb2 pc14- o s c32_in pa7 pa4 pa2 pa15 pb11 pb1 pa6 pa3 h pb10 pc5 pc4 d pa8 pa9 boot0 pb8 c pc9 pa11 pb6 pc12 v dda pb9 b pa12 pc10 pc15- o s c32_out pb3 pd2 a 8 7 6 5 4 3 2 1 v ss _4 o s c_in o s c_out v dd_4 g f e pc2 v ref+ pc13- tamper-rtc pb4 pa13 pa14 pb7 pb5 v ss _3 pc7 pc8 pc0 nr s t pc1 pb0 pa5 pb14 v dd_2 v dd_3 pb13 v bat pc11 pa10 v ss _2 v ss _1 pc6 v ss a pa1 v dd_1 pb15 pb12 pa0-wkup pinouts and pin description stm32f103x8, stm32f103xb 26/105 docid13587 rev 16 figure 8. stm32f103xx performance line lqfp48 pinout figure 9. stm32f103xx performance line ufqfpn48 pinout 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 12 13 14 15 16 17 18 19 20 21 22 1 2 3 4 5 6 7 8 9 10 11 48 47 46 45 pa 3 pa 4 pa 5 pa 6 pa 7 pb0 pb1 pb2 pb10 pb11 v ss _1 vdd_1 vdd_2 v ss _2 pa 1 3 pa 1 2 pa 1 1 pa 1 0 pa 9 pa 8 pb15 pb14 pb13 pb12 vbat pc13-tamper-rtc pc14-o s c32_in pc15-o s c32_out pd0-o s c_in pd1-o s c_out nr s t v ss a vdda pa 0 - w k u p pa 1 pa 2 vdd_3 v ss _3 pb9 pb8 boot0 pb7 pb6 pb5 pb4 pb3 pa 1 5 pa 1 4 lqfp48 a i14393 b ms31472v1 vdd_3 vss_3 pb9 pb8 boot0 pb7 pb6 pb5 pb4 pb3 pa15 pa14 pa3 pa4 pa5 pa6 pa7 pb0 pb1 pb2 pb10 pb11 vss_1 vdd_1 vbat pc13-tamper-rtc pc14-osc32_in pc15-osc32_out pd0-osc_in pd1-osc_out nrst vssa vdda pa0-wkup pa1 pa2 vdd_2 vss_2 pa13 pa12 pa11 pa10 pa9 pa8 pb15 pb14 pb13 pb12 48 qfpn48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 13 14 15 16 17 18 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 docid13587 rev 16 27/105 stm32f103x8, stm32f103xb pinouts and pin description 104 figure 10. stm32f103xx performance line vfqfpn36 pinout v ss _3 boot0 pb7 pb6 pb5 pb4 pb3 pa15 pa14 36 35 34 33 32 31 30 29 28 v dd_3 1 27 v dd_2 o s c_in/pd0 2 26 v ss _2 o s c_out/pd1 3 25 pa13 nr s t 4 qfn36 24 pa12 v ss a 5 23 pa11 v dda 6 22 pa10 pa0-wkup 7 21 pa 9 pa 1 8 20 pa 8 pa 2 9 19 v dd_1 10 11 12 13 14 15 16 17 18 pa 3 pa 4 pa 5 pa 6 pa 7 pb0 pb1 pb2 v ss _1 a i14654 pinouts and pin description stm32f103x8, stm32f103xb 28/105 docid13587 rev 16 table 5. medium-density st m32f103xx pin definitions pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap a3 b2 - - - 1 - pe2 i/o ft pe2 traceck b3 a1 - - - 2 - pe3 i/o ft pe3 traced0 c3 b1 - - - 3 - pe4 i/o ft pe4 traced1 d3 c2 - - - 4 - pe5 i/o ft pe5 traced2 e3 d2 - - - 5 - pe6 i/o ft pe6 traced3 b2 e2 1 b2 1 6 - v bat sv bat a2 c1 2 a2 2 7 - pc13-tamper- rtc (5) i/o pc13 (6) tamper-rtc a1 d1 3 a1 3 8 - pc14-osc32_in (5) i/o pc14 (6) osc32_in b1 e1 4 b1 4 9 - pc15- osc32_out (5) i/o pc15 (6) osc32_out c2 f2 - - - 10 - v ss_5 sv ss_5 d2 g2 - - - 11 - v dd_5 sv dd_5 c1 f1 5 c1 5 12 2 osc_in i osc_in pd0 (7) d1 g1 6 d1 6 13 3 osc_out o osc_out pd1 (7) e1 h2 7 e1 7 14 4 nrst i/o nrst f1 h1 - e3 8 15 - pc0 i/o pc0 adc12_in10 f2 j2 - e2 9 16 - pc1 i/o pc1 adc12_in11 e2 j3 - f2 10 17 - pc2 i/o pc2 adc12_in12 f3 k2 - - (8) 11 18 - pc3 i/o pc3 adc12_in13 g1 j1 8 f1 12 19 5 v ssa sv ssa h1 k1 - - - 20 - v ref- sv ref- j1 l1 - g1 (8) -21- v ref+ sv ref+ k1 m1 9 h1 13 22 6 v dda sv dda docid13587 rev 16 29/105 stm32f103x8, stm32f103xb pinouts and pin description 104 g2 l2 10 g2 14 23 7 pa0-wkup i/o pa0 wkup/ usart2_cts (9) / adc12_in0/ tim2_ch1_ etr (9) h2 m2 11 h2 15 24 8 pa1 i/o pa1 usart2_rts (9) / adc12_in1/ tim2_ch2 (9) j2 k3 12 f3 16 25 9 pa2 i/o pa2 usart2_tx (9) / adc12_in2/ tim2_ch3 (9) k2 l3 13 g3 17 26 10 pa3 i/o pa3 usart2_rx (9) / adc12_in3/ tim2_ch4 (9) e4 e3 - c2 18 27 - v ss_4 sv ss_4 f4 h3 - d2 19 28 - v dd_4 sv dd_4 g3 m3 14 h3 20 29 11 pa4 i/o pa4 spi1_nss (9) / usart2_ck (9) / adc12_in4 h3 k4 15 f4 21 30 12 pa5 i/o pa5 spi1_sck (9) / adc12_in5 j3 l4 16 g4 22 31 13 pa6 i/o pa6 spi1_miso (9) / adc12_in6/ tim3_ch1 (9) tim1_bkin k3 m4 17 h4 23 32 14 pa7 i/o pa7 spi1_mosi (9) / adc12_in7/ tim3_ch2 (9) tim1_ch1n g4 k5 - h5 24 33 pc4 i/o pc4 adc12_in14 h4 l5 - h6 25 34 pc5 i/o pc5 adc12_in15 j4 m5 18 f5 26 35 15 pb0 i/o pb0 adc12_in8/ tim3_ch3 (9) tim1_ch2n k4 m6 19 g5 27 36 16 pb1 i/o pb1 adc12_in9/ tim3_ch4 (9) tim1_ch3n table 5. medium-density stm32f 103xx pin definitions (continued) pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap pinouts and pin description stm32f103x8, stm32f103xb 30/105 docid13587 rev 16 g5 l6 20 g6 28 37 17 pb2 i/o ft pb2/boot1 h5 m7 - - - 38 - pe7 i/o ft pe7 tim1_etr j5 l7 - - - 39 - pe8 i/o ft pe8 tim1_ch1n k5 m8 - - - 40 - pe9 i/o ft pe9 tim1_ch1 g6 l8 - - - 41 - pe10 i/o ft pe10 tim1_ch2n h6 m9 - - - 42 - pe11 i/o ft pe11 tim1_ch2 j6 l9 - - - 43 - pe12 i/o ft pe12 tim1_ch3n k6 m10 - - - 44 - pe13 i/o ft pe13 tim1_ch3 g7 m11 - - - 45 - pe14 i/o ft pe14 tim1_ch4 h7 m12 - - - 46 - pe15 i/o ft pe15 tim1_bkin j7 l10 21 g7 29 47 - pb10 i/o ft pb10 i2c2_scl/ usart3_tx (9) tim2_ch3 k7 l11 22 h7 30 48 - pb11 i/o ft pb11 i2c2_sda/ usart3_rx (9) tim2_ch4 e7 f12 23 d6 31 49 18 v ss_1 sv ss_1 f7 g12 24 e6 32 50 19 v dd_1 sv dd_1 k8 l12 25 h8 33 51 - pb12 i/o ft pb12 spi2_nss/ i2c2_smbal/ usart3_ck (9) / tim1_bkin (9) j8 k12 26 g8 34 52 - pb13 i/o ft pb13 spi2_sck/ usart3_cts (9) / tim1_ch1n (9) h8 k11 27 f8 35 53 - pb14 i/o ft pb14 spi2_miso/ usart3_rts (9) tim1_ch2n (9) g8 k10 28 f7 36 54 - pb15 i/o ft pb15 spi2_mosi/ tim1_ch3n (9) k9 k9 - - - 55 - pd8 i/o ft pd8 usart3_tx j9 k8 - - - 56 - pd9 i/o ft pd9 usart3_rx table 5. medium-density stm32f 103xx pin definitions (continued) pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap docid13587 rev 16 31/105 stm32f103x8, stm32f103xb pinouts and pin description 104 h9 j12 - - - 57 - pd10 i/o ft pd10 usart3_ck g9 j11 - - - 58 - pd11 i/o ft pd11 usart3_cts k10 j10 - - - 59 - pd12 i/o ft pd12 tim4_ch1 / usart3_rts j10 h12 - - - 60 - pd13 i/o ft pd13 tim4_ch2 h10 h11 - - - 61 - pd14 i/o ft pd14 tim4_ch3 g10 h10 - - - 62 - pd15 i/o ft pd15 tim4_ch4 f10 e12 - f6 37 63 - pc6 i/o ft pc6 tim3_ch1 e10 e11 e7 38 64 - pc7 i/o ft pc7 tim3_ch2 f9 e10 e8 39 65 - pc8 i/o ft pc8 tim3_ch3 e9 d12 - d8 40 66 - pc9 i/o ft pc9 tim3_ch4 d9 d11 29 d7 41 67 20 pa8 i/o ft pa8 usart1_ck/ tim1_ch1 (9) / mco c9 d10 30 c7 42 68 21 pa9 i/o ft pa9 usart1_tx (9) / tim1_ch2 (9) d10 c12 31 c6 43 69 22 pa10 i/o ft pa10 usart1_rx (9) / tim1_ch3 (9) c10 b12 32 c8 44 70 23 pa11 i/o ft pa11 usart1_cts/ canrx (9) / usbdm/ tim1_ch4 (9) b10 a12 33 b8 45 71 24 pa12 i/o ft pa12 usart1_rts/ cantx (9) /usbdp tim1_etr (9) a10 a11 34 a8 46 72 25 pa13 i/o ft jtms/swdio pa13 f8 c11 - - - 73 - not connected e6 f11 35 d5 47 74 26 v ss_2 sv ss_2 f6 g11 36 e5 48 75 27 v dd_2 sv dd_2 table 5. medium-density stm32f 103xx pin definitions (continued) pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap pinouts and pin description stm32f103x8, stm32f103xb 32/105 docid13587 rev 16 a9 a10 37 a7 49 76 28 pa14 i/o ft jtck/swclk pa14 a8 a9 38 a6 50 77 29 pa15 i/o ft jtdi tim2_ch1_ etr/ pa15 /spi1_nss b9 b11 - b7 51 78 pc10 i/o ft pc10 usart3_tx b8 c10 - b6 52 79 pc11 i/o ft pc11 usart3_rx c8 b10 - c5 53 80 pc12 i/o ft pc12 usart3_ck - c9 - c1 - 81 2 pd0 i/o ft pd0 canrx - b9 - d1 - 82 3 pd1 i/o ft pd1 cantx b7 c8 b5 54 83 - pd2 i/o ft pd2 tim3_etr c7 b8 - - - 84 - pd3 i/o ft pd3 usart2_cts d7 b7 - - - 85 - pd4 i/o ft pd4 usart2_rts b6 a6 - - - 86 - pd5 i/o ft pd5 usart2_tx c6 b6 - - - 87 - pd6 i/o ft pd6 usart2_rx d6 a5 - - - 88 - pd7 i/o ft pd7 usart2_ck a7 a8 39 a5 55 89 30 pb3 i/o ft jtdo tim2_ch2 / pb3 traceswo spi1_sck a6 a7 40 a4 56 90 31 pb4 i/o ft jntrst tim3_ch1/ pb4/ spi1_miso c5 c5 41 c4 57 91 32 pb5 i/o pb5 i2c1_smbal tim3_ch2 / spi1_mosi b5 b5 42 d3 58 92 33 pb6 i/o ft pb6 i2c1_scl (9) / tim4_ch1 (9) usart1_tx a5 b4 43 c3 59 93 34 pb7 i/o ft pb7 i2c1_sda (9) / tim4_ch2 (9) usart1_rx d5 a4 44 b4 60 94 35 boot0 i boot0 table 5. medium-density stm32f 103xx pin definitions (continued) pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap docid13587 rev 16 33/105 stm32f103x8, stm32f103xb pinouts and pin description 104 b4 a3 45 b3 61 95 - pb8 i/o ft pb8 tim4_ch3 (9) i2c1_scl / canrx a4 b3 46 a3 62 96 - pb9 i/o ft pb9 tim4_ch4 (9) i2c1_sda/ cantx d4 c3 - - - 97 - pe0 i/o ft pe0 tim4_etr c4 a2 - - - 98 - pe1 i/o ft pe1 e5 d3 47 d4 63 99 36 v ss_3 sv ss_3 f5 c4 48 e4 64 100 1 v dd_3 sv dd_3 1. i = input, o = output, s = supply. 2. ft = 5 v tolerant. 3. function availability depends on the chosen device. for devices having reduced peripher al counts, it is always the lower number of peripheral that is included. for example, if a device has only one spi and two usarts, they will be called spi1 and usart1 & usart2, respectively. refer to table 2 on page 10 . 4. if several peripherals share the same i/o pin, to avoid c onflict between these alternate f unctions only one peripheral should be enabled at a time through the peri pheral clock enable bit (in the correspondi ng rcc peripheral clock enable register). 5. pc13, pc14 and pc15 are supplied through the power switch. si nce the switch only sinks a limited amount of current (3 ma), the use of gpios pc13 to pc15 in output mode is limited: the speed should not exceed 2 mhz with a maximum load of 30 pf and these ios must not be used as a current source (e.g. to drive an led). 6. main function after the first backup domain power-up. lat er on, it depends on the contents of the backup registers even after reset (because these registers are not reset by the main reset). for details on how to manage these ios, refer to the battery backup domain and bkp register desc ription sections in the stm32f10xxx reference manual, available from the stmicroelectronics w ebsite: www.st.com. 7. the pins number 2 and 3 in the vfqfpn36 package, 5 and 6 in the lqfp48, ufqfp48 and lqfp64 packages, and c1 and c2 in the tfbga64 package are configured as osc_in/osc _out after reset, however the functionality of pd0 and pd1 can be remapped by software on these pins. for the lqfp100 package, pd0 and pd1 ar e available by default, so there is no need for remapping. for more details, refer to the alternate function i/o and debug configuration section in the stm32f10xxx reference manual. the use of pd0 and pd1 in output mode is limited as they can only be used at 50 mhz in output mode. 8. unlike in the lqfp64 package, there is no pc3 in the tfbga64 package. the v ref+ functionality is provided instead. 9. this alternate function can be remapped by software to some other port pins (if availabl e on the used package). for more details, refer to the alternate function i/o and debug configurat ion section in the stm32f10xxx reference manual, available from the stmicroelectroni cs website: www.st.com. table 5. medium-density stm32f 103xx pin definitions (continued) pins pin name type (1) i / o level (2) main function (3) (after reset) alternate functions (4) lfbga100 ufbg100 lqfp48/ufqfpn48 tfbga64 lqfp64 lqfp100 vfqfpn36 default remap memory mapping stm32f103x8, stm32f103xb 34/105 docid13587 rev 16 4 memory mapping the memory map is shown in figure 11 . figure 11. memory map re s erved 0x4000 0000 0x4000 0400 0x4000 0800 0x4000 0c00 0x4000 2800 0x4000 2c00 0x4000 3000 0x4000 3400 0x4000 3800 0x4000 3c00 0x4000 4400 0x4000 4800 0x4000 4c00 0x4001 0c00 0x4001 1000 0x4001 1400 0x4001 1800 0x4002 1400 apb memory s p a ce dma 0x4002 1000 tim2 reserved 0x4001 0800 0x4001 1c00 0x4001 2400 0x4001 2800 0x4001 2c00 0x4001 3000 0x4001 3400 0x4001 3800 tim3 tim4 re s erved rtc wwdg iwdg re s erved s pi2 u s art2 u s art3 afio port a port c port d re s e rve d adc1 re s erved u s art1 re s erved 0x4002 0400 0x4002 0000 0x4001 3c00 0x4000 5400 0x4000 5800 re s erved adc2 tim1 s pi1 re s erved i2c1 bkp 0x4000 6000 0x4000 5c00 por t e pwr port b i2c2 re s erved b xcan exti re s erved rcc re s erved fl as h interf a ce re s erved re s erved re s erved 0x4000 6400 0x4000 6800 0x4000 6c00 0x4000 7000 0x4000 7400 0x4001 0000 0x4001 0400 0x4002 2000 0x4002 2400 0x4002 3000 0x4002 3400 0x6000 0000 0xe010 0000 re s erved 0xffff ffff u s b reg i s ter s crc 0 1 2 3 4 5 6 7 0x2000 0000 0x4000 0000 0x6000 0000 0x8000 0000 0xa000 0000 0xc000 0000 0xe000 0000 0xffff ffff 0x0000 0000 peripher a l s s ram fl as h memory re s e rved re s e rved 0x0800 0000 0x0801 ffff 0x1fff f000 0x1fff ffff s y s tem memory option byte s 0x1fff f800 0x1fff f80f cortex- m3 intern a l peripher a l s 0xe010 0000 a i14394f s h a red 512 b yte u s b/can s ram ali as ed to fl as h or s y s tem memory depending on boot pin s 0x0000 0000 docid13587 rev 16 35/105 stm32f103x8, stm32f103xb electrical characteristics 104 5 electrical characteristics 5.1 parameter conditions unless otherwise specified, all voltages are referenced to v ss . 5.1.1 minimum and maximum values unless otherwise specified the minimum and ma ximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and frequencies by tests in production on 100% of the devices with an ambient temperature at t a = 25 c and t a = t a max (given by the selected temperature range). data based on characterization results, design simulation and/or technology characteristics are indicated in the table footnotes and are not tested in production. based on characterization, the minimum and maximum values refer to sample tests and represent the mean value plus or minus three times the standard deviation (mean3 ? ). 5.1.2 typical values unless otherwise specified, typical data are based on t a = 25 c, v dd = 3.3 v (for the 2v ? v dd ? 3.6 v voltage range). they are given only as design guidelines and are not tested. typical adc accuracy values are determined by characterization of a batch of samples from a standard diffusion lot over the full temperature range, where 95% of the devices have an error less than or equal to the value indicated (mean2 ? ) . 5.1.3 typical curves unless otherwise specified, all typical curves are given only as design guidelines and are not tested. 5.1.4 loading capacitor the loading conditions used for pin parameter measurement are shown in figure 12 . 5.1.5 pin input voltage the input voltage measurement on a pin of the device is described in figure 13 . electrical characteristics stm32f103x8, stm32f103xb 36/105 docid13587 rev 16 5.1.6 power supply scheme figure 14. power supply scheme caution: in figure 14 , the 4.7 f capacitor must be connected to v dd3 . figure 12. pin loading conditi ons figure 13. pin input voltage a i14141 c = 50 pf s tm32f103xx pin a i14142 s tm32f103xx pin v in a i14125d v dd 1/2/3/4/5 an a lo g: rc s , pll, ... po wer s wi tch v bat gp i/o s out in kernel logic (cpu, digit a l & memorie s ) b a ck u p circ u itry (o s c32k,rtc, b a ck u p regi s ter s ) w a ke- u p logic 5 100 nf + 1 4.7 f 1.8-3.6v reg u l a tor v ss 1/2/3/4/5 v dda v ref+ v ref- v ss a adc level s hifter io logic v dd 10 nf + 1 f v ref 10 nf + 1 f v dd docid13587 rev 16 37/105 stm32f103x8, stm32f103xb electrical characteristics 104 5.1.7 current consumption measurement figure 15. current consum ption measurement scheme 5.2 absolute maximum ratings stresses above the absolute maximum ratings listed in table 6: voltage characteristics , table 7: current characteristics , and table 8: thermal characteristics may cause permanent damage to the device. these are stress ratings only and functional ope ration of the device at these conditions is not im plied. exposure to maximum rating conditions for extended periods may affect device reliability. a i14126 v bat v dd v dda i dd _v bat i dd table 6. voltage characteristics symbol ratings min max unit v dd ?? v ss external main supply voltage (including v dda and v dd ) (1) 1. all main power (v dd , v dda ) and ground (v ss , v ssa ) pins must always be connected to the external power supply, in the permitted range. ?0.3 4.0 v v in (2) 2. v in maximum must always be respected. refer to table 7: current characteristics for the maximum allowed injected current values. input voltage on five volt tolerant pin v ss ? 0.3 v dd ? 4.0 input voltage on any other pin v ss ?? 0.3 4.0 | ? v ddx | variations between different v dd power pins 50 mv |v ssx ?? v ss | variations between all the different ground pins 50 v esd(hbm) electrostatic discharge voltage (human body model) see section 5.3.11: absolute maximum ratings (electrical sensitivity) electrical characteristics stm32f103x8, stm32f103xb 38/105 docid13587 rev 16 5.3 operating conditions 5.3.1 general operating conditions table 7. current characteristics symbol ratings max. unit i vdd total current into v dd /v dda power lines (source) (1) 1. all main power (v dd , v dda ) and ground (v ss , v ssa ) pins must always be connected to the external power supply, in the permitted range. 150 ma i vss total current out of v ss ground lines (sink) (1) 150 i io output current sunk by any i/o and control pin 25 output current source by any i/os and control pin ? 25 i inj(pin) (2) 2. negative injection disturbs the analog performance of the device. see note 2. on page 77 . injected current on five volt tolerant pins (3) 3. positive injection is not possible on thes e i/os. a negative injection is induced by v in electrical characteristics stm32f103x8, stm32f103xb 40/105 docid13587 rev 16 5.3.3 embedded reset and power control block characteristics the parameters given in table 11 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . table 11. embedded reset and power control block characteristics symbol parameter conditions min typ max unit v pvd programmable voltage detector level selection pls[2:0]=000 (rising edge) 2.1 2.18 2.26 v pls[2:0]=000 (falling edge) 2 2.08 2.16 pls[2:0]=001 (rising edge) 2.19 2.28 2.37 pls[2:0]=001 (falling edge) 2.09 2.18 2.27 pls[2:0]=010 (rising edge) 2.28 2.38 2.48 pls[2:0]=010 (falling edge) 2.18 2.28 2.38 pls[2:0]=011 (rising edge) 2.38 2.48 2.58 pls[2:0]=011 (falling edge) 2.28 2.38 2.48 pls[2:0]=100 (rising edge) 2.47 2.58 2.69 pls[2:0]=100 (falling edge) 2.37 2.48 2.59 pls[2:0]=101 (rising edge) 2.57 2.68 2.79 pls[2:0]=101 (falling edge) 2.47 2.58 2.69 pls[2:0]=110 (rising edge) 2.66 2.78 2.9 pls[2:0]=110 (falling edge) 2.56 2.68 2.8 pls[2:0]=111 (rising edge) 2.76 2.88 3 pls[2:0]=111 (falling edge) 2.66 2.78 2.9 v pvdhyst (2) pvd hysteresis 100 mv v por/pdr power on/power down reset threshold falling edge 1.8 (1) 1. the product behavior is guaranteed by design down to the minimum v por/pdr value. 1.88 1.96 v rising edge 1.84 1.92 2.0 v pdrhyst (2) pdr hysteresis 40 mv t rsttempo (2) 2. guaranteed by design, not tested in production. reset temporization 1 2.5 4.5 ms docid13587 rev 16 41/105 stm32f103x8, stm32f103xb electrical characteristics 104 5.3.4 embedded reference voltage the parameters given in table 12 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . 5.3.5 supply current characteristics the current consumption is a function of several parameters and factors such as the operating voltage, ambient temperature, i/o pi n loading, device software configuration, operating frequencies, i/o pin switching rate, program location in memory and executed binary code. the current consumption is measured as described in figure 15: current consumption measurement scheme . all run-mode current consumption measurements given in this section are performed with a reduced code that gives a consumption equivalent to dhrystone 2.1 code. maximum current consumption the mcu is placed under the following conditions: ? all i/o pins are in input mode with a static value at v dd or v ss (no load) ? all peripherals are disabled ex cept when explicitly mentioned ? the flash memory access time is adjusted to the f hclk frequency (0 wait state from 0 to 24 mhz, 1 wait state from 24 to 48 mhz and 2 wait states above) ? prefetch in on (reminder: this bit must be set before clock setting and bus prescaling) ? when the peripherals are enabled f pclk1 = f hclk /2, f pclk2 = f hclk the parameters given in table 13 , table 14 and table 15 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . table 12. embedded internal reference voltage symbol parameter conditions min typ max unit v refint internal reference voltage ?40 c < t a < +105 c 1.16 1.20 1.26 v ?40 c < t a < +85 c 1.16 1.20 1.24 t s_vrefint (1) 1. shortest sampling time can be determined in the application by multiple iterations. adc sampling time when reading the internal reference voltage 5.1 17.1 (2) 2. guaranteed by design, not tested in production. s v rerint (2) internal reference voltage spread over the temperature range v dd = 3 v 10 mv 10 mv t coeff (2) temperature coefficient 100 ppm/c electrical characteristics stm32f103x8, stm32f103xb 42/105 docid13587 rev 16 table 13. maximum current consumption in run mode, code with data processing running from flash symbol parameter conditions f hclk max (1) 1. based on characterization, not tested in production. unit t a = 85 c t a = 105 c i dd supply current in run mode external clock (2) , all peripherals enabled 2. external clock is 8 mhz and pll is on when f hclk > 8 mhz. 72 mhz 50 50.3 ma 48 mhz 36.1 36.2 36 mhz 28.6 28.7 24 mhz 19.9 20.1 16 mhz 14.7 14.9 8 mhz 8.6 8.9 external clock (2) , all peripherals disabled 72 mhz 32.8 32.9 48 mhz 24.4 24.5 36 mhz 19.8 19.9 24 mhz 13.9 14.2 16 mhz 10.7 11 8 mhz 6.8 7.1 table 14. maximum current consumption in run mode, code with data processing running from ram symbol parameter conditions f hclk max (1) 1. based on characterization, tested in production at v dd max, f hclk max. unit t a = 85 c t a = 105 c i dd supply current in run mode external clock (2) , all peripherals enabled 2. external clock is 8 mhz and pll is on when f hclk > 8 mhz. 72 mhz 48 50 ma 48 mhz 31.5 32 36 mhz 24 25.5 24 mhz 17.5 18 16 mhz 12.5 13 8 mhz 7.5 8 external clock (2) , all peripherals disabled 72 mhz 29 29.5 48 mhz 20.5 21 36 mhz 16 16.5 24 mhz 11.5 12 16 mhz 8.5 9 8 mhz 5.5 6 docid13587 rev 16 43/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 16. typical current consumption in run mode versus frequency (at 3.6 v) - code with data processing running from ram, peripherals enabled figure 17. typical current consumption in run mode versus frequency (at 3.6 v) - code with data processing running from ram, peripherals disabled 0 5 10 15 20 25 30 35 40 45 -40 0 25 70 85 105 temper a t u re (c) con su mption (ma) 72 mhz 36 mhz 16 mhz 8 mhz 0 5 10 15 20 25 30 -40 0 25 70 85 105 temper a t u re (c) con su mption (ma) 72 mhz 36 mhz 16 mhz 8 mhz electrical characteristics stm32f103x8, stm32f103xb 44/105 docid13587 rev 16 table 15. maximum current consumption in sleep mode, code running from flash or ram symbol parameter conditions f hclk max (1) 1. based on characterization, tested in production at v dd max , f hclk max with peripherals enabled. unit t a = 85 c t a = 105 c i dd supply current in sleep mode external clock (2) , all peripherals enabled 2. external clock is 8 mhz and pll is on when f hclk > 8 mhz. 72 mhz 30 32 ma 48 mhz 20 20.5 36 mhz 15.5 16 24 mhz 11.5 12 16 mhz 8.5 9 8 mhz 5.5 6 external clock (2) , all peripherals disabled 72 mhz 7.5 8 48 mhz 6 6.5 36 mhz 5 5.5 24 mhz 4.5 5 16 mhz 4 4.5 8 mhz 3 4 docid13587 rev 16 45/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 18. typical current consumption on v bat with rtc on versus temperature at different v bat values table 16. typical and maximum current consumptions in stop and standby modes symbol parameter conditions typ (1) max unit v dd /v bat = 2.0 v v dd /v bat = 2.4 v v dd /v bat = 3.3 v t a = 85 c t a = 105 c i dd supply current in stop mode regulator in run mode, low-speed and high-speed internal rc oscillators and high-speed oscillator off (no independent watchdog) - 23.5 24 200 370 a regulator in low power mode, low- speed and high-speed internal rc oscillators and high-speed oscillator off (no independent watchdog) - 13.5 14 180 340 supply current in standby mode low-speed internal rc oscillator and independent watchdog on -2.63.4-- low-speed internal rc oscillator on, independent watchdog off -2.43.2-- low-speed internal rc oscillator and independent watchdog off, low- speed oscillator and rtc off -1.7245 i dd_vbat backup domain supply current low-speed oscillator and rtc on 0.9 1.1 1.4 1.9 (2) 2.2 1. typical values are measured at t a = 25 c. 2. based on characterization, not tested in production. 0 0.5 1 1.5 2 2.5 ?40 c 25 c 70 c 8 5 c 105 c temperature (c) consumption ( a ) 2 v 2.4 v 3 v 3 .6 v ai17 3 51 electrical characteristics stm32f103x8, stm32f103xb 46/105 docid13587 rev 16 figure 19. typical current consumption in stop mode with regulator in run mode versus temperature at v dd = 3.3 v and 3.6 v figure 20. typical current consumption in stop mode with regulator in low-power mode versus temperature at v dd = 3.3 v and 3.6 v 0 50 100 150 200 250 300 -45 25 70 90 110 temper a t u re (c) con su mption (a) 3.3 v 3.6 v 0 50 100 150 200 250 300 -40 0 25 70 85 105 temper a t u re (c) con su mption (a) 3.3 v 3.6 v docid13587 rev 16 47/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 21. typical current consumption in standby mode versus temperature at v dd = 3.3 v and 3.6 v typical current consumption the mcu is placed under the following conditions: ? all i/o pins are in input mode with a static value at v dd or v ss (no load). ? all peripherals are disabled except if it is explicitly mentioned. ? the flash access time is adjusted to f hclk frequency (0 wait state from 0 to 24 mhz, 1 wait state from 24 to 48 mhz and 2 wait states above). ? ambient temperature and v dd supply voltage conditions summarized in table 9 . ? prefetch is on (reminder: this bit must be set before clock setting and bus prescaling) ? when the peripherals are enabled f pclk1 = f hclk /4, f pclk 2 = f hclk /2, f adcclk = f pclk2 /4 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 ?45 c 25 c 85 c 105 c temper a t u re (c) con su mption (a) 3.3 v 3.6 v electrical characteristics stm32f103x8, stm32f103xb 48/105 docid13587 rev 16 table 17. typical current consumption in run mode, code with data processing running from flash symbol parameter conditions f hclk typ (1) 1. typical values are measures at t a = 25 c, v dd = 3.3 v. unit all peripherals enabled (2) 2. add an additional power consumption of 0.8 ma per adc for the analog part. in applications, this consumption occurs only while the adc is on (adon bit is set in the adc_cr2 register). all peripherals disabled i dd supply current in run mode external clock (3) 3. external clock is 8 mhz and pll is on when f hclk > 8 mhz. 72 mhz 36 27 ma 48 mhz 24.2 18.6 36 mhz 19 14.8 24 mhz 12.9 10.1 16 mhz 9.3 7.4 8 mhz 5.5 4.6 4 mhz 3.3 2.8 2 mhz 2.2 1.9 1 mhz 1.6 1.45 500 khz 1.3 1.25 125 khz 1.08 1.06 running on high speed internal rc (hsi), ahb prescaler used to reduce the frequency 64 mhz 31.4 23.9 ma 48 mhz 23.5 17.9 36 mhz 18.3 14.1 24 mhz 12.2 9.5 16 mhz 8.5 6.8 8 mhz 4.9 4 4 mhz 2.7 2.2 2 mhz 1.6 1.4 1 mhz 1.02 0.9 500 khz 0.73 0.67 125 khz 0.5 0.48 docid13587 rev 16 49/105 stm32f103x8, stm32f103xb electrical characteristics 104 table 18. typical current consumption in sleep mode, code running from flash or ram symbol parameter conditions f hclk typ (1) 1. typical values are measures at t a = 25 c, v dd = 3.3 v. unit all peripherals enabled (2) 2. add an additional power consumption of 0.8 ma per adc for the analog part. in applications, this consumption occurs only while the adc is on (adon bit is set in the adc_cr2 register). all peripherals disabled i dd supply current in sleep mode external clock (3) 3. external clock is 8 mhz and pll is on when f hclk > 8 mhz. 72 mhz 14.4 5.5 ma 48 mhz 9.9 3.9 36 mhz 7.6 3.1 24 mhz 5.3 2.3 16 mhz 3.8 1.8 8 mhz 2.1 1.2 4 mhz 1.6 1.1 2 mhz 1.3 1 1 mhz 1.11 0.98 500 khz 1.04 0.96 125 khz 0.98 0.95 running on high speed internal rc (hsi), ahb prescaler used to reduce the frequency 64 mhz 12.3 4.4 48 mhz 9.3 3.3 36 mhz 7 2.5 24 mhz 4.8 1.8 16 mhz 3.2 1.2 8 mhz 1.6 0.6 4 mhz 1 0.5 2 mhz 0.72 0.47 1 mhz 0.56 0.44 500 khz 0.49 0.42 125 khz 0.43 0.41 electrical characteristics stm32f103x8, stm32f103xb 50/105 docid13587 rev 16 on-chip peripheral current consumption the current consumption of the on -chip peripherals is given in table 19 . the mcu is placed under the following conditions: ? all i/o pins are in input mode with a static value at v dd or v ss (no load) ? all peripherals are disabled unless otherwise mentioned ? the given value is calculated by measuring the current consumption ? with all peripherals clocked off ? with only one peripheral clocked on ? ambient operating temperature and v dd supply voltage conditions summarized in table 6 table 19. peripheral current consumption (1) 1. f hclk = 72 mhz, f apb1 = f hclk /2, f apb2 = f hclk , default prescaler value for each peripheral. peripheral typical consumption at 25 c unit apb1 tim2 1.2 ma tim3 1.2 tim4 0.9 spi2 0.2 usart2 0.35 usart3 0.35 i2c1 0.39 i2c2 0.39 usb 0.65 can 0.72 apb2 gpio a 0.47 ma gpio b 0.47 gpio c 0.47 gpio d 0.47 gpio e 0.47 adc1 (2) 2. specific conditions for adc: f hclk = 56 mhz, f apb1 = f hclk /2, f apb2 = f hclk , f adcclk = f apb2/4 , adon bit in the adc_cr2 register is set to 1. 1.81 adc2 1.78 tim1 1.6 spi1 0.43 usart1 0.85 docid13587 rev 16 51/105 stm32f103x8, stm32f103xb electrical characteristics 104 5.3.6 external clock source characteristics high-speed external user clock generated from an external source the characteristics given in table 20 result from tests performed using an high-speed external clock source, and under ambient temperature and supply voltage conditions summarized in table 9 . low-speed external user clock generated from an external source the characteristics given in table 21 result from tests performed using an low-speed external clock source, and under ambient temperature and supply voltage conditions summarized in table 9 . table 20. high-speed external user clock characteristics symbol parameter conditions min typ max unit f hse_ext user external clock source frequency (1) 1825mhz v hseh osc_in input pin high level voltage 0.7v dd -v dd v v hsel osc_in input pin low level voltage v ss -0.3v dd t w(hse) t w(hse) osc_in high or low time (1) 1. guaranteed by design, not tested in production. 5-- ns t r(hse) t f(hse) osc_in rise or fall time (1) --20 c in(hse) osc_in input capacitance (1) -5-pf ducy (hse) duty cycle 45 - 55 % i l osc_in input leakage current v ss ? v in ? v dd --1a table 21. low-speed external user clock characteristics symbol parameter conditions min typ max unit f lse_ext user external clock source frequency (1) 1. guaranteed by design, not tested in production. 32.768 1000 khz v lseh osc32_in input pin high level voltage 0.7v dd -v dd v v lsel osc32_in input pin low level voltage v ss -0.3v dd t w(lse) t w(lse) osc32_in high or low time (1) 450 - - ns t r(lse) t f(lse) osc32_in rise or fall time (1) --50 c in(lse) osc32_in input capacitance (1) -5-pf ducy (lse) duty cycle 30 - 70 % i l osc32_in input leakage current v ss ? v in ? v dd --1a electrical characteristics stm32f103x8, stm32f103xb 52/105 docid13587 rev 16 figure 22. high-speed external clock source ac timing diagram figure 23. low-speed external clock source ac timing diagram high-speed external clock generated from a crystal/ceramic resonator the high-speed external (hse) clock can be supplied with a 4 to 16 mhz crystal/ceramic resonator oscillator. all th e information given in this paragraph are based on characterization results obtained with typical external components specified in table 22 . in the application, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion an d startup stabilization time. refer to the crystal resonator manufacturer for more details on the resonator characteristics (frequenc y, package, accuracy). a i14143 o s c_in exter nal s tm32f103xx clo ck s o urc e v h s eh t f(h s e) t w(h s e) i l 90% 10% t h s e t t r(h s e) t w(h s e) f h s e_ext v h s el a i14144 b o s c32_in exter nal s tm32f103xx clo ck s o urc e v l s eh t f(l s e) t w(l s e) i l 90% 10% t l s e t t r(l s e) t w(l s e) f l s e_ext v l s el docid13587 rev 16 53/105 stm32f103x8, stm32f103xb electrical characteristics 104 for c l1 and c l2 , it is recommended to use high-quality external ceramic capacitors in the 5 pf to 25 pf range (typ.), designed for high- frequency applications, and selected to match the requirements of the crystal or resonator (see figure 24 ). c l1 and c l2 are usually the same size. the crystal manufacturer typically specifies a load capacitance which is the series combination of c l1 and c l2 . pcb and mcu pin capacitance must be included (10 pf can be used as a rough estimate of the comb ined pin and board capacitance) when sizing c l1 and c l2 . refer to the application note an28 67 ?oscillator design guide for st microcontrollers? available from the st website www.st.com. figure 24. typical application with an 8 mhz crystal 1. r ext value depends on the cr ystal characteristics. low-speed external clock generated from a crystal/ceramic resonator the low-speed external (lse) clock can be supplied with a 32.768 khz crystal/ceramic resonator oscillator. all th e information given in this paragraph are based on characterization results obtained with typical external components specified in table 23 . in the application, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion an d startup stabilization time. refer to the crystal resonator manufacturer for more details on the resonator characteristics (frequenc y, package, accuracy). table 22. hse 4-16 mhz oscillator characteristics (1) (2) 1. resonator characteristics given by the crystal/ceramic resonator manufacturer. 2. based on characterization, not tested in production. symbol parameter conditions min typ max unit f osc_in oscillator frequency 4 8 16 mhz r f feedback resistor - 200 - k ? c recommended load capacitance versus equivalent serial resistance of the crystal (r s ) (3) 3. the relatively low value of the rf resistor offers a good protection against issues resulting from use in a humid environment, due to the induced leakage and t he bias condition change. however, it is recommended to take this point into account if the mcu is used in tough humidity conditions. r s = 30 ?? -30-pf i 2 hse driving current v dd = 3.3 v, v in =v ss with 30 pf load --1ma g m oscillator transconductance startup 25 - - ma/v t su(hse (4) 4. t su(hse) is the startup time measured from the moment it is enabled (by software) to a stabilized 8 mhz oscillation is reached. this value is measured for a standard crystal res onator and it can vary significantly with the crystal manufacturer startup time v dd is stabilized - 2 - ms a i14145 o s c_ou t o s c_in f h s e c l1 r f s tm32f103xx 8 mh z re s on a tor r ext (1) c l2 re s on a tor with integr a ted c a p a citor s bi as controlled g a in electrical characteristics stm32f103x8, stm32f103xb 54/105 docid13587 rev 16 note: for c l1 and c l2 it is recommended to use high-quality ceramic capacitors in the 5 pf to 15 pf range selected to match the requirements of the crystal or resonator. c l1 and c l2, are usually the same size. the crystal manufacture r typically specifies a load capacitance which is the series combination of c l1 and c l2 . load capacitance c l has the following formula: c l = c l1 x c l2 / ( c l1 + c l2 ) + c stray where c stray is the pin capacitance and board or trace pcb-related capacitance. typically, it is between 2 pf and 7 pf. caution: to avoid exceeding the maximum value of c l1 and c l2 (15 pf) it is strongly recommended to use a resonator with a load capacitance c l ? 7 pf. never use a resonator with a load capacitance of 12.5 pf. example: if you choose a resonator with a load capacitance of c l = 6 pf, and c stray = 2 pf, then c l1 = c l2 = 8 pf. table 23. lse oscillator characteristics (f lse = 32.768 khz) (1) (2) symbol parameter conditions min typ max unit r f feedback resistor - 5 - m ? c recommended load capacitance versus equivalent serial resistance of the crystal (r s ) r s = 30 k ? - - 15 pf i 2 lse driving current v dd = 3.3 v v in = v ss --1.4a g m oscillator transconductance 5 - - a/v t su(lse) (3) startup time v dd is stabilized t a = 50 c - 1.5 - s t a = 25 c - 2.5 - t a = 10 c - 4 - t a = 0 c - 6 - t a = -10 c - 10 - t a = -20 c - 17 - t a = -30 c - 32 - t a = -40 c - 60 - 1. based on characterization, not tested in production. 2. refer to the note and caution paragraphs below the table, and to the application note an2867 ?oscillator design guide for st microcontrollers?. 3. t su(lse) is the startup time measured from the moment it is ena bled (by software) to a stabilized 32.768 khz oscillation is reached. this value is measured for a st andard crystal and it can vary signif icantly with the crystal manufacturer docid13587 rev 16 55/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 25. typical applicati on with a 32.768 khz crystal 5.3.7 internal clock source characteristics the parameters given in table 24 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . high-speed internal (hsi) rc oscillator a i14146 o s c32_ou t o s c32_in f l s e c l1 r f s tm32f103xx 32.768 kh z re s on a tor c l2 re s on a tor with integr a ted c a p a citor s bi as controlled g a in table 24. hsi oscillator characteristics (1) 1. v dd = 3.3 v, t a = ?40 to 105 c unless otherwise specified. symbol parameter conditions min typ max unit f hsi frequency - 8 - mhz ducy (hsi) duty cycle 45 - 55 % acc hsi accuracy of the hsi oscillator user-trimmed with the rcc_cr register (2) 2. refer to application note an2868 ?stm32f10xxx internal rc oscillator (hsi) calibration? available from the st website www.st.com. --1 (3) 3. guaranteed by design, not tested in production. factory- calibrated (4)(5) 4. based on characterization, not tested in production. 5. the actual frequency of hsi oscillator may be impacted by a reflow, but does not drift out of the specified range. t a = ?40 to 105 c ?2 - 2.5 t a = ?10 to 85 c ?1.5 - 2.2 t a = 0 to 70 c ?1.3 - 2 t a = 25 c ?1.1 - 1.8 t su(hsi) (4) hsi oscillator startup time 1-2s i dd(hsi) (4) hsi oscillator power consumption - 80 100 a electrical characteristics stm32f103x8, stm32f103xb 56/105 docid13587 rev 16 low-speed internal (lsi) rc oscillator wakeup time from low-power mode the wakeup times given in table 26 is measured on a wakeup phase with a 8-mhz hsi rc oscillator. the clock source used to wake up the device depends from the curren t operating mode: ? stop or standby mode: the clo ck source is the rc oscillator ? sleep mode: the clock source is the clock that was set before entering sleep mode. all timings are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . table 25. lsi oscillator characteristics (1) 1. v dd = 3 v, t a = ?40 to 105 c unless otherwise specified. symbol parameter min typ max unit f lsi (2) 2. based on characterization, not tested in production. frequency 30 40 60 khz t su(lsi) (3) 3. guaranteed by design, not tested in production. lsi oscillator startup time - - 85 s i dd(lsi) (3) lsi oscillator power consumption - 0.65 1.2 a docid13587 rev 16 57/105 stm32f103x8, stm32f103xb electrical characteristics 104 5.3.8 pll characteristics the parameters given in table 27 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . 5.3.9 memory characteristics flash memory the characteristics are given at t a = ? 40 to 105 c unless otherwise specified. table 26. low-power mode wakeup timings symbol parameter typ unit t wusleep (1) 1. the wakeup times are measured from the wakeup even t to the point in which the user application code reads the first instruction. wakeup from sleep mode 1.8 s t wustop (1) wakeup from stop mode (regulator in run mode) 3.6 wakeup from stop mode (regulator in low power mode) 5.4 t wustdby (1) wakeup from standby mode 50 table 27. pll characteristics symbol parameter value unit min (1) 1. based on characterization, not tested in production. typ max (1) f pll_in pll input clock (2) 2. take care of using the appropriate multiplier factors so as to have pll input cloc k values compatible with the range defined by f pll_out . 18.0 25 mhz pll input clock duty cycle 40 - 60 % f pll_out pll multiplier output clock 16 - 72 mhz t lock pll lock time - - 200 s jitter cycle-to-cycle jitter - - 300 ps table 28. flash memory characteristics symbol parameter conditions min (1) typ max (1) unit t prog 16-bit programming time t a ??? ?40 to +105 c 40 52.5 70 s t erase page (1 kb) erase time t a ?? ?40 to +105 c 20 - 40 ms t me mass erase time t a ?? ?40 to +105 c 20 - 40 electrical characteristics stm32f103x8, stm32f103xb 58/105 docid13587 rev 16 table 29. flash memory endurance and data retention 5.3.10 emc characteristics susceptibility tests are perf ormed on a sample basis duri ng device characterization. functional ems (electromagnetic susceptibility) while a simple application is executed on t he device (toggling 2 leds through i/o ports). the device is stressed by two electromagnetic events until a failure o ccurs. the failure is indicated by the leds: ? electrostatic discharge (esd) (positive and negative) is applied to all device pins until a functional disturbance occurs. this test is compliant with the iec 61000-4-2 standard. ? ftb : a burst of fast transient voltage (positive and negative) is applied to v dd and v ss through a 100 pf capacitor, until a func tional disturbance occurs. this test is compliant with the iec 61000-4-4 standard. a device reset allows normal operations to be resumed. the test results are given in table 30 . they are based on the ems levels and classes defined in application note an1709. i dd supply current read mode f hclk = 72 mhz with 2 wait states, v dd = 3.3 v --20 ma write / erase modes f hclk = 72 mhz, v dd = 3.3 v --5 power-down mode / halt, v dd = 3.0 to 3.6 v --50a v prog programming voltage 2 - 3.6 v 1. guaranteed by design, not tested in production. symbol parameter conditions value unit min (1) 1. based on characterization, not tested in production. typ max n end endurance t a = ?40 to +85 c (6 suffix versions) t a = ?40 to +105 c (7 suffix versions) 10 - - kcycles t ret data retention 1 kcycle (2) at t a = 85 c 2. cycling performed over the whole temperature range. 30 - - years 1 kcycle (2) at t a = 105 c 10 - - 10 kcycles (2) at t a = 55 c 20 - - table 28. flash memory characteristics (continued) symbol parameter conditions min (1) typ max (1) unit docid13587 rev 16 59/105 stm32f103x8, stm32f103xb electrical characteristics 104 designing hardened software to avoid noise problems emc characterization and optimization are per formed at component level with a typical application environment and simplified mcu soft ware. it should be noted that good emc performance is highly dependent on the user application and the software in particular. therefore it is recommended that the user applies emc software optimization and prequalification tests in re lation with the emc level requested for his application. software recommendations the software flowchart must include the m anagement of runaway conditions such as: ? corrupted program counter ? unexpected reset ? critical data corruption (control registers...) prequalification trials most of the common failures (unexpected reset and program counter corruption) can be reproduced by manually forci ng a low state on the nrst pin or the oscillator pins for 1 second. to complete these trials, esd stress can be applie d directly on the device, over the range of specification values. when unexpected behavior is detected, the software can be hardened to prevent unrecoverable errors occurring (see application note an1015). electromagnetic interference (emi) the electromagnetic field emitted by the device are monitored while a simple application is executed (toggling 2 leds through the i/o por ts). this emission test is compliant with iec 61967-2 standard which specifies the test board and the pin loading. table 30. ems characteristics symbol parameter conditions level/ class v fesd voltage limits to be applied on any i/o pin to induce a functional disturbance v dd ?? 3.3 v, t a ?? +25 c, f hclk ?? 72 mhz conforms to iec 61000-4-2 2b v eftb fast transient voltage burst limits to be applied through 100 pf on v dd and v ss pins to induce a functional disturbance v dd ??? 3.3 v, t a ?? +25 c, f hclk ?? 72 mhz conforms to iec 61000-4-4 4a table 31. emi characteristics symbol parameter conditions monitored frequency band max vs. [f hse /f hclk ] unit 8/48 mhz 8/72 mhz s emi peak level v dd ?? 3.3 v, t a ?? 25 c, lqfp100 package compliant with iec 61967-2 0.1 to 30 mhz 12 12 dbv 30 to 130 mhz 22 19 130 mhz to 1ghz 23 29 sae emi level 4 4 - electrical characteristics stm32f103x8, stm32f103xb 60/105 docid13587 rev 16 5.3.11 absolute maximum ratings (electrical sensitivity) based on three different tests (esd, lu) using specific measurement methods, the device is stressed in order to determ ine its performance in terms of electrical sensitivity. electrostatic discharge (esd) electrostatic discharges (a positive then a negative pulse separated by 1 second) are applied to the pins of each sample according to each pin combinati on. the sample size depends on the number of supply pins in the device (3 parts (n+1) supply pins). this test conforms to the jesd22-a114/c101 standard. static latch-up two complementary static te sts are required on six pa rts to assess the latch-up performance: ? a supply overvoltage is applied to each power supply pin ? a current injection is applied to each input, output and configurable i/o pin these tests are compliant with eia/jesd 78a ic latch-up standard. table 32. esd absolute maximum ratings symbol ratings conditions class maximum value (1) 1. based on characterization results, not tested in production. unit v esd(hbm) electrostatic discharge voltage (human body model) t a ?? +25 c conforming to jesd22-a114 22000 v v esd(cdm) electrostatic discharge voltage (charge device model) t a ?? +25 c conforming to ansi/esd stm5.3.1 ii 500 table 33. electri cal sensitivities symbol parameter conditions class lu static latch-up class t a ?? +105 c conforming to jesd78a ii level a docid13587 rev 16 61/105 stm32f103x8, stm32f103xb electrical characteristics 104 5.3.12 i/o current in jection characteristics as a general rule, current injection to the i/o pins, due to external voltage below v ss or above v dd (for standard, 3 v-capable i/o pins) should be avoided during normal product operation. however, in order to give an indica tion of the robustness of the microcontroller in cases when abnormal injection ac cidentally happens, susceptib ility tests are pe rformed on a sample basis during device characterization. functional susceptibilty to i/o current injection while a simple application is executed on the de vice, the device is stressed by injecting current into the i/o pins programmed in floating input mode . while current is injected into the i/o pin, one at a time, the device is checked for functional failures. the failure is indicated by an out of range parameter: adc error above a certain limit (>5 lsb tue), out of spec current injection on adja cent pins or other functional failure (for example reset, oscillator frequency deviation). the test results are given in table 34 table 34. i/o current injection susceptibility symbol description functional susceptibility unit negative injection positive injection i inj injected current on osc_in32, osc_out32, pa4, pa5, pc13 -0 +0 ma injected current on all ft pins -5 +0 injected current on any other pin -5 +5 electrical characteristics stm32f103x8, stm32f103xb 62/105 docid13587 rev 16 5.3.13 i/o port characteristics general input/output characteristics unless otherwise specified, the parameters given in table 35 are derived from tests performed under the conditions summarized in table 9 . all i/os are cmos and ttl compliant. table 35. i/o static characteristics symbol parameter conditions min typ max unit v il low level input voltage standard io input low level voltage - - 0.28*(v dd -2 v)+0.8 v (1) v io ft (3) input low level voltage - - 0.32*(v dd -2v)+0.75 v (1) all i/os except boot0 - - 0.35v dd (2) v ih high level input voltage standard io input high level voltage 0.41*(v dd -2 v)+1.3 v (1) -- io ft (3) input high level voltage 0.42*(v dd -2 v)+1 v (1) -- all i/os except boot0 0.65v dd (2) -- v hys standard io schmitt trigger voltage hysteresis (4) 200 - - mv io ft schmitt trigger voltage hysteresis (4) 5% v dd (5) -- i lkg input leakage current (6) v ss ?? v in ?? v dd standard i/os -- ? 1 a v in = 5 v i/o ft --3 r pu weak pull-up equivalent resistor (7) v in ?? v ss 30 40 50 k ? r pd weak pull-down equivalent resistor (7) v in ?? v dd 30 40 50 c io i/o pin capacitance - 5 - pf 1. data based on design simulation. 2. tested in production. 3. ft = five-volt tolerant. in order to sustain a voltage higher than v dd +0.3 the internal pull-up/pull-down resistors must be disabled. 4. hysteresis voltage between schmitt trigger switching leve ls. based on characterization, not tested in production. 5. with a minimum of 100 mv. 6. leakage could be higher than max. if negativ e current is injected on adjacent pins. docid13587 rev 16 63/105 stm32f103x8, stm32f103xb electrical characteristics 104 7. pull-up and pull-down resistor s are designed with a true resistance in seri es with a switchable pmos/nmos. this pmos/nmos contribution to the series resistance is minimum (~10% order) . electrical characteristics stm32f103x8, stm32f103xb 64/105 docid13587 rev 16 all i/os are cmos and ttl compliant (no software configuration required). their characteristics cover more than the strict cmos-technology or ttl parameters. the coverage of these requirements is shown in figure 26 and figure 27 for standard i/os, and in figure 28 and figure 29 for 5 v tolerant i/os. figure 26. standard i/o input characteristics - cmos port figure 27. standard i/o input characteristics - ttl port ai17277c v dd (v) 1.3 0.8 2 3.6 2.7 3 0.7 cmos standard requirement v ih =0.65v dd 3.3 v ih /v il (v) 7 ilmax 7 ihmin tested in production v dd -2)+0.8 =0.28(v il cmos standard requirement v il =0.35v dd v ih =0.41(v dd -2)+1.3 tested in production based on design simulations based on design simulations area not determined ai17278b 2 3.6 v ih /v il (v) 1.3 2.0 0.8 2.16 ttl requirements v ih =2v v ih =0.41(v dd -2)+1.3 v il =0.28(v dd -2)+0.8 ttl requirements v il =0.8v 1.96 1.25 v dd (v) 7 ilmax 7 ihmin based on design simulations based on design simulations area not determined docid13587 rev 16 65/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 28. 5 v tolerant i/o inpu t characteristics - cmos port figure 29. 5 v tolerant i/o input characteristics - ttl port vdd 1.3 2 3.6 cmos standard requirements v ih =0.65v dd cmos standard requirment v il =0.35v dd 1.67 1 2.7 0.7 33.3 1 0.75 1.295 0.975 1.42 1.07 1.55 1.16 v ih /v il (v) v dd (v) ai17279c v ih =0.42(v dd -2)+1 v il =0.32(v dd -2)+0.75 based on design simulations based on design simulations tested in production tested in production area not determined 2.0 0.8 2 3.6 2.16 1.67 1 0.75 ttl requirement v ih =2v ttl requirements v il =0.8v v ih /v il (v) v dd (v) 7 ilmax 7 ihmin ai17280b v ih =0.42*(v dd -2)+1 v il =0.32*(v dd -2)+0.75 based on design simulations based on design simulations area not determined electrical characteristics stm32f103x8, stm32f103xb 66/105 docid13587 rev 16 output driving current the gpios (general-purpose inputs/outputs) can sink or source up to 8 ma, and sink or source up to 20 ma (with a relaxed v ol /v oh ) except pc13, pc14 and pc15 which can sink or source up to +/-3ma. when using the gpios pc13 to pc15 in output mode, the speed should not exceed 2 mhz with a maximum load of 30 pf. in the user application, the number of i/o pi ns which can drive curr ent must be limited to respect the absolute maximum rating specified in section 5.2 : ? the sum of the currents sourced by all the i/os on v dd, plus the maximum run consumption of the mcu sourced on v dd, cannot exceed the absolute maximum rating i vdd (see table 7 ). ? the sum of the currents sunk by all the i/os on v ss plus the maximum run consumption of the mcu sunk on v ss cannot exceed the absolute maximum rating i vss (see table 7 ). output voltage levels unless otherwise specified, the parameters given in table 36 are derived from tests performed under ambient temperature and v dd supply voltage conditions summarized in table 9 . all i/os are cmos and ttl compliant. table 36. output voltage characteristics symbol parameter conditions min max unit v ol (1) 1. the i io current sunk by the device must always re spect the absolute maximu m rating specified in table 7 and the sum of i io (i/o ports and control pins) must not exceed i vss . output low level voltage for an i/o pin when 8 pins are sunk at same time cmos port (2) , i io = +8 ma 2.7 v < v dd < 3.6 v 2. ttl and cmos outputs are compatible with jedec standards jesd36 and jesd52. -0.4 v v oh (3) 3. the i io current sourced by the device must always re spect the absolute maximum rating specified in table 7 and the sum of i io (i/o ports and control pins) must not exceed i vdd . output high level voltage for an i/o pin when 8 pins are sourced at same time v dd ?0.4 - v ol (1) output low level voltage for an i/o pin when 8 pins are sunk at same time ttl port (2) i io =+ 8ma 2.7 v < v dd < 3.6 v -0.4 v oh (3) output high level voltage for an i/o pin when 8 pins are sourced at same time 2.4 - v ol (1)(4) 4. based on characterization data, not tested in production. output low level voltage for an i/o pin when 8 pins are sunk at same time i io = +20 ma 2.7 v < v dd < 3.6 v -1.3 v oh (3)(4) output high level voltage for an i/o pin when 8 pins are sourced at same time v dd ?1.3 - v ol (1)(4) output low level voltage for an i/o pin when 8 pins are sunk at same time i io = +6 ma 2 v < v dd < 2.7 v -0.4 v oh (3)(4) output high level voltage for an i/o pin when 8 pins are sourced at same time v dd ?0.4 - docid13587 rev 16 67/105 stm32f103x8, stm32f103xb electrical characteristics 104 input/output ac characteristics the definition and values of input/output ac characteristics are given in figure 30 and table 37 , respectively. unless otherwise specified, the parameters given in table 37 are derived from tests performed under the ambient temperature and v dd supply voltage conditions summarized in table 9 . table 37. i/o ac characteristics (1) 1. the i/o speed is configur ed using the modex[1:0] bits. refer to the stm32f10xxx reference manual for a description of gpio port configuration register. modex[1:0] bit value (1) symbol parameter conditions min max unit 10 f max(io)out maximum frequency (2) 2. the maximum frequency is defined in figure 30 . c l = 50 pf, v dd = 2 v to 3.6 v - 2 mhz t f(io)out output high to low level fall time c l = 50 pf, v dd = 2 v to 3.6 v -125 (3) 3. guaranteed by design, not tested in production. ns t r(io)out output low to high level rise time -125 (3) 01 f max(io)out maximum frequency (2) c l = 50 pf, v dd = 2 v to 3.6 v - 10 mhz t f(io)out output high to low level fall time c l = 50 pf, v dd = 2 v to 3.6 v -25 (3) ns t r(io)out output low to high level rise time -25 (3) 11 f max(io)out maximum frequency (2) c l = 30 pf, v dd = 2.7 v to 3.6 v - 50 mhz c l = 50 pf, v dd = 2.7 v to 3.6 v - 30 c l = 50 pf, v dd = 2 v to 2.7 v - 20 t f(io)out output high to low level fall time c l = 30 pf, v dd = 2.7 v to 3.6 v - 5 (3) ns c l = 50 pf, v dd = 2.7 v to 3.6 v - 8 (3) c l = 50 pf, v dd = 2 v to 2.7 v - 12 (3) t r(io)out output low to high level rise time c l = 30 pf, v dd = 2.7 v to 3.6 v - 5 (3) c l = 50 pf, v dd = 2.7 v to 3.6 v - 8 (3) c l = 50 pf, v dd = 2 v to 2.7 v - 12 (3) -t extipw pulse width of external signals detected by the exti controller 10 - ns electrical characteristics stm32f103x8, stm32f103xb 68/105 docid13587 rev 16 figure 30. i/o ac charac teristics definition 5.3.14 nrst pin characteristics the nrst pin input driver uses cmos technology. it is connected to a permanent pull-up resistor, r pu (see table 35 ). unless otherwise specified, the parameters given in table 38 are derived from tests performed under the ambient temperature and v dd supply voltage conditions summarized in table 9 . ai14131c 10% 90% 50% t r(io)out output external on 50pf maximum frequency is achieved if (t r + t f ) 2/3)t and if the duty cycle is (45-55%) 10% 50% 90% when loaded by 50pf t t f(io)out table 38. nrst pin characteristics symbol parameter conditions min typ max unit v il(nrst) (1) 1. guaranteed by design, not tested in production. nrst input low level voltage ?0.5 - 0.8 v v ih(nrst) (1) nrst input high level voltage 2 - v dd +0.5 v hys(nrst) nrst schmitt trigger voltage hysteresis - 200 - mv r pu weak pull-up equivalent resistor (2) 2. the pull-up is designed with a true resistance in se ries with a switchable pmos. this pmos contribution to the series resistance must be minimum (~10% order) . v in ?? v ss 30 40 50 k ? v f(nrst) (1) nrst input filtered pulse - - 100 ns v nf(nrst) (1) nrst input not filtered pulse 300 - - ns docid13587 rev 16 69/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 31. recommended nrst pin protection 2. the reset network protects t he device against par asitic resets. 3. the user must ensure that the level on the nrst pin can go below the v il(nrst) max level specified in table 38 . otherwise the reset will not be taken into account by the device. 5.3.15 tim time r characteristics the parameters given in table 39 are guaranteed by design. refer to section 5.3.12: i/o current injection char acteristics for details on the input/output alternate function characteristics (output comp are, input capture, external clock, pwm output). ai141 3 2d stm32f10x r pu nrst (2) v dd filter internal reset 0.1 f external reset circuit (1) table 39. timx (1) characteristics 1. timx is used as a general term to refer to the tim1, tim2, tim3 and tim4 timers. symbol parameter conditions min max unit t res(tim) timer resolution time 1- t timxclk f timxclk = 72 mhz 13.9 - ns f ext timer external clock frequency on ch1 to ch4 0 f timxclk /2 mhz f timxclk = 72 mhz 036mhz res tim timer resolution - 16 bit t counter 16-bit counter clock period when internal clock is selected 1 65536 t timxclk f timxclk = 72 mhz 0.0139 910 s t max_count maximum possible count - 65536 65536 t timxclk f timxclk = 72 mhz -59.6 s electrical characteristics stm32f103x8, stm32f103xb 70/105 docid13587 rev 16 5.3.16 communications interfaces i 2 c interface characteristics the stm32f103xx performance line i 2 c interface meets the requirements of the standard i 2 c communication protocol with the following re strictions: the i/o pins sda and scl are mapped to are not ?true? open-drain. when co nfigured as open-drain, the pmos connected between the i/o pin and v dd is disabled, but is still present. the i 2 c characteristics are described in table 40 . refer also to section 5.3.12: i/o current injection characteristics for more details on the input/output alternate function characteristics (sda and scl) . table 40. i 2 c characteristics symbol parameter standard mode i 2 c (1) 1. guaranteed by design, not tested in production. fast mode i 2 c (1)(2) 2. f pclk1 must be at least 2 mhz to achieve standard mode i 2 c frequencies. it must be at least 4 mhz to achieve fast mode i 2 c frequencies. it must be a multiple of 10 mhz to reach the 400 khz maximum i2c fast mode clock. unit min max min max t w(scll) scl clock low time 4.7 - 1.3 - s t w(sclh) scl clock high time 4.0 - 0.6 t su(sda) sda setup time 250 - 100 - ns t h(sda) sda data hold time 0 - 0 900 (3) 3. the maximum data hold time has only to be met if the interface does not stretch the low period of scl signal. t r(sda) t r(scl) sda and scl rise time - 1000 20 + 0.1c b 300 t f(sda) t f(scl) sda and scl fall time - 300 - 300 t h(sta) start condition hold time 4.0 - 0.6 - s t su(sta) repeated start condition setup time 4.7 - 0.6 - t su(sto) stop condition setup time 4.0 - 0.6 - ? s t w(sto:sta) stop to start condition time (bus free) 4.7 - 1.3 - ? s c b capacitive load for each bus line - 400 - 400 pf docid13587 rev 16 71/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 32. i 2 c bus ac waveforms and measurement circuit 1. measurement points are done at cmos levels: 0.3v dd and 0.7v dd . 2. rs = series protection resistors, rp = pull-up resistors, v dd_i2c = i2c bus supply. table 41. scl frequency (f pclk1 = 36 mhz.,v dd_i2c = 3.3 v) (1)(2) 1. r p = external pull-up resistance, f scl = i 2 c speed, 2. for speeds around 200 khz, the tole rance on the achieved speed is of ? 5%. for other speed ranges, the tolerance on the achieved speed ? 2%. these variations depend on the accuracy of the external components used to design the application. f scl (khz) i2c_ccr value r p = 4.7 k ? 400 0x801e 300 0x8028 200 0x803c 100 0x00b4 50 0x0168 20 0x0384 ai14133e start sd a i2c bus v dd_i2c v dd_i2c stm32f10x sda scl t f(sda) t r(sda) scl t h(sta) t w(sclh) t w(scll) t su(sda) t r(scl) t f(scl) t h(sda) start repeated start t su(sta) t su(sto) stop t su(sto:sta) rp rp rs rs electrical characteristics stm32f103x8, stm32f103xb 72/105 docid13587 rev 16 spi interface characteristics unless otherwise specified, the parameters given in table 42 are derived from tests performed under the ambient temperature, f pclkx frequency and v dd supply voltage conditions su mmarized in table 9 . refer to section 5.3.12: i/o current injection char acteristics for more details on the input/output alternate function char acteristics (nss, sck, mosi, miso). table 42. spi characteristics symbol parameter con ditions min max unit f sck 1/t c(sck) spi clock frequency master mode - 18 mhz slave mode - 18 t r(sck) t f(sck) spi clock rise and fall time capacitive load: c = 30 pf - 8 ns ducy(sck) spi slave input clock duty cycle slave mode 30 70 % t su(nss) (1) 1. based on characterization, not tested in production. nss setup time slave mode 4t pclk - ns t h(nss) (1) nss hold time slave mode 2t pclk - t w(sckh) (1) t w(sckl) (1) sck high and low time master mode, f pclk = 36 mhz, presc = 4 50 60 t su(mi) (1) t su(si) (1) data input setup time master mode 5 - slave mode 5 - t h(mi) (1) data input hold time master mode 5 - t h(si) (1) slave mode 4 - t a(so) (1)(2) 2. min time is for the minimum time to drive the output and the max time is for the maximum time to validate the data. data output access time slave mode, f pclk = 20 mhz 0 3t pclk t dis(so) (1)(3) 3. min time is for the minimum time to invalidate the output and the max time is for the maximum time to put the data in hi-z data output disable time slave mode 2 10 t v(so) (1) data output valid time slave mode (after enable edge) 25 t v(mo) (1) data output valid time master mode (after enable edge) 5 t h(so) (1) data output hold time slave mode (after enable edge) 15 - t h(mo) (1) master mode (after enable edge) 2 - docid13587 rev 16 73/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 33. spi timing diagram - slave mode and cpha = 0 figure 34. spi timing diagram - slave mode and cpha = 1 (1) 1. measurement points are done at cmos levels: 0.3v dd and 0.7v dd . a i14134c s ck inp u t cpha= 0 mo s i input mi s o out p ut cpha= 0 m s bout m s bin bi t6 ou t l s bin l s bout cpol=0 cpol=1 bit1 in n ss inp u t t s u(n ss ) t c( s ck) t h(n ss ) t a ( s o) t w( s ckh) t w( s ckl) t v( s o) t h( s o) t r( s ck) t f( s ck) t di s ( s o) t su ( s i) t h( s i) a i14135 s ck inp u t cpha=1 mo s i input mi s o out p ut cpha=1 m s bout m s bin bi t6 ou t l s bin l s bout cpol=0 cpol=1 bit1 in t s u(n ss ) t c( s ck) t h(n ss ) t a ( s o) t w( s ckh) t w( s ckl) t v( s o) t h( s o) t r( s ck) t f( s ck) t di s ( s o) t su ( s i) t h( s i) n ss inp u t electrical characteristics stm32f103x8, stm32f103xb 74/105 docid13587 rev 16 figure 35. spi timing diagram - master mode (1) 1. measurement points are done at cmos levels: 0.3v dd and 0.7v dd . usb characteristics the usb interface is usb- if certified (full speed). table 43. usb startup time symbol parameter max unit t startup (1) 1. guaranteed by design, not tested in production. usb transceiver startup time 1 s a i14136 s ck inp u t cpha= 0 mo s i outut mi s o inp ut cpha= 0 m s bin m s b out bi t6 in l s b out l s b in cpol=0 cpol=1 b i t1 out n ss inp u t t c( s ck) t w( s ckh) t w( s ckl) t r( s ck) t f( s ck) t h(mi) high s ck inp u t cpha=1 cpha=1 cpol=0 cpol=1 t su (mi) t v(mo) t h(mo) docid13587 rev 16 75/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 36. usb timings: definition of data signal rise and fall time 5.3.17 can (controller ar ea network) interface refer to section 5.3.12: i/o current injection char acteristics for more details on the input/output alternate function characteristics (can_tx and can_rx). table 44. usb dc electrical characteristics symbol parameter conditions min. (1) 1. all the voltages are measured from the local ground potential. max. (1) unit input levels v dd usb operating voltage (2) 2. to be compliant with the usb 2.0 full-speed electric al specification, the usbd p (d+) pin should be pulled up with a 1.5 k ? resistor to a 3.0-to-3.6 v voltage range. 3.0 (3) 3. the stm32f103xx usb functionality is ensured dow n to 2.7 v but not the full usb electrical characteristics which are degraded in the 2.7-to-3.0 v v dd voltage range. 3.6 v v di (4) 4. guaranteed by design, not tested in production. differential input sensitivity i(usbdp, usbdm) 0.2 - v v cm (4) differential common mode range includes v di range 0.8 2.5 v se (4) single ended receiver threshold 1.3 2.0 output levels v ol static output level low r l of 1.5 k ? to 3.6 v (5) 5. r l is the load connected on the usb drivers -0.3 v v oh static output level high r l of 15 k ? to v ss (5) 2.8 3.6 table 45. usb: full-speed electrical characteristics (1) 1. guaranteed by design, not tested in production. symbol parameter conditions min max unit driver characteristics t r rise time (2) 2. measured from 10% to 90% of the data signal. for more detailed informations, please refer to usb specification - chapter 7 (version 2.0). c l = 50 pf 420ns t f fall time (2) c l = 50 pf 4 20 ns t rfm rise/ fall time matching t r /t f 90 110 % v crs output signal crossover voltage 1.3 2.0 v a i14137 t f differen ti a l d a t a line s v ss v cr s t r cro ss over point s electrical characteristics stm32f103x8, stm32f103xb 76/105 docid13587 rev 16 5.3.18 12-bit adc characteristics unless otherwise specified, the parameters given in table 46 are derived from tests performed under the ambient temperature, f pclk2 frequency and v dda supply voltage conditions su mmarized in table 9 . note: it is recommended to perform a calibration after each power-up. table 46. adc characteristics symbol parameter conditions min typ max unit v dda power supply 2.4 - 3.6 v v ref+ positive reference voltage 2.4 - v dda v i vref current on the v ref input pin 160 (1) 220 (1) a f adc adc clock frequency 0.6 - 14 mhz f s (2) sampling rate 0.05 - 1 mhz f trig (2) external trigger frequency f adc = 14 mhz - - 823 khz --171/f adc v ain (3) conversion voltage range 0 (v ssa or v ref- tied to ground) -v ref+ v r ain (2) external input impedance see equation 1 and table 47 for details --50k ? r adc (2) sampling switch resistance - - 1 k ? c adc (2) internal sample and hold capacitor --8pf t cal (2) calibration time f adc = 14 mhz 5.9 s 83 1/f adc t lat (2) injection trigger conversion latency f adc = 14 mhz - - 0.214 s --3 (4) 1/f adc t latr (2) regular trigger conversion latency f adc = 14 mhz - - 0.143 s --2 (4) 1/f adc t s (2) sampling time f adc = 14 mhz 0.107 - 17.1 s 1.5 - 239.5 1/f adc t stab (2) power-up time 0 0 1 s t conv (2) total conversion time (including sampling time) f adc = 14 mhz 1 - 18 s 14 to 252 (t s for sampling +12.5 for successive approximation) 1/f adc 1. based on characterization, not tested in production. 2. guaranteed by design, not tested in production. 3. in devices delivered in vfqfpn and lqfp packages, v ref+ is internally connected to v dda and v ref- is internally connected to v ssa . devices that come in the tfbga64 package have a v ref+ pin but no v ref- pin (v ref- is internally connected to v ssa ), see table 5 and figure 7 . 4. for external triggers, a delay of 1/f pclk2 must be added to the latency specified in table 46 . docid13587 rev 16 77/105 stm32f103x8, stm32f103xb electrical characteristics 104 equation 1: r ain max formula: the formula above ( equation 1 ) is used to determine the maximum external impedance allowed for an error below 1/4 of lsb. here n = 12 (from 12-bit resolution). table 47. r ain max for f adc = 14 mhz (1) 1. based on characterization, not tested in production. t s (cycles) t s (s) r ain max (k ? ) 1.5 0.11 0.4 7.5 0.54 5.9 13.5 0.96 11.4 28.5 2.04 25.2 41.5 2.96 37.2 55.5 3.96 50 71.5 5.11 na 239.5 17.1 na table 48. adc accuracy - limited test conditions (1) (2) 1. adc dc accuracy values are measured after internal calibration. 2. adc accuracy vs. negative injection current: inject ing a negative current on any analog input pins should be avoided as this signific antly reduces the accuracy of the conv ersion being performed on another analog input. it is recommended to add a schottky diode (pin to ground) to analog pins which may potentially inject negative currents. any positive injection current with in the limits specified for i inj(pin) and ? i inj(pin) in section 5.3.12 does not affect the adc accuracy. symbol parameter test conditions typ max (3) 3. based on characterization, not tested in production. unit et total unadjusted error f pclk2 = 56 mhz, f adc = 14 mhz, r ain < 10 k ? , v dda = 3 v to 3.6 v t a = 25 c measurements made after adc calibration 1.3 2 lsb eo offset error 1 1.5 eg gain error 0.5 1.5 ed differential linearity error 0.7 1 el integral linearity error 0.8 1.5 r ain t s f adc c adc 2 n2 + ?? ln ? ? ------------------------------------------------------------- - r adc ? ? electrical characteristics stm32f103x8, stm32f103xb 78/105 docid13587 rev 16 figure 37. adc accuracy characteristics table 49. adc accuracy (1) (2) (3) 1. adc dc accuracy values are measured after internal calibration. 2. better performance could be achieved in restricted v dd , frequency and temperature ranges. 3. adc accuracy vs. negative injection current: injecting negative current on any of the standard (non- robust) analog input pins should be av oided as this significantly reduce s the accuracy of the conversion being performed on another analog input. it is recommend ed to add a schottky diode (pin to ground) to standard analog pins which may potentially inject negative current. any positive injection current with in the limits specified for i inj(pin) and ? i inj(pin) in section 5.3.12 does not affect the adc accuracy. symbol parameter test conditions typ max (4) 4. based on characterization, not tested in production. unit et total unadjusted error f pclk2 = 56 mhz, f adc = 14 mhz, r ain < 10 k ? , v dda = 2.4 v to 3.6 v measurements made after adc calibration 2 5 lsb eo offset error 1.5 2.5 eg gain error 1.5 3 ed differential linearity error 1 2 el integral linearity error 1.5 3 e o e g 1l s b ideal (1) ex a mple of a n a ct ua l tr a n s fer c u rve (2) the ide a l tr a n s fer c u rve (3) end point correl a tion line e t =tot a l un a dj us ted error: m a xim u m devi a tion b etween the a ct ua l a nd the ide a l tr a n s fer c u rve s . e o =off s et error: devi a tion b etween the fir s t a ct ua l tr a n s ition a nd the fir s t ide a l one. e g =g a in error: devi a tion b etween the l as t ide a l tr a n s ition a nd the l as t a ct ua l one. e d =differenti a l line a rity error: m a xim u m devi a tion b etween a ct ua l s tep s a nd the ide a l one. e l =integr a l line a rity error: m a xim u m devi a tion b etween a ny a ct ua l tr a n s ition a nd the end point correl a tion line. 4095 4094 4093 5 4 3 2 1 0 7 6 1234567 4093 4094 4095 4096 (1) (2) e t e d e l (3) v dda v ss a ai14 3 95b v ref+ 4096 (or depending on p a ck a ge)] v dda 4096 [1l s b ideal = docid13587 rev 16 79/105 stm32f103x8, stm32f103xb electrical characteristics 104 figure 38. typical connecti on diagram using the adc 1. refer to table 46 for the values of r ain , r adc and c adc . 2. c parasitic represents the capacitance of the pcb (dependent on soldering and pcb layout quality) plus the pad capacitance (roughly 7 pf). a high c parasitic value will downgrade conversion accuracy. to remedy this, f adc should be reduced. general pcb design guidelines power supply decoupling should be performed as shown in figure 39 or figure 40 , depending on whether v ref+ is connected to v dda or not. the 10 nf capacitors should be ceramic (good quality). they should be placed them as close as possible to the chip. figure 39. power supply and reference decoupling (v ref+ not connected to v dda ) 1. v ref+ and v ref? inputs are available only on 100-pin packages. a i14150c s tm32f103xx v dd ainx i l 1 a 0.6 v v t r ain (1) c p a r as itic v ain 0.6 v v t r adc (1) 12- b it converter c adc (1) sa mple a nd hold adc converter v ref+ ( s ee note 1) s tm32f103xx v dda v ss a /v ref? ( s ee note 1) 1 f // 10 nf 1 f // 10 nf a i14388 b electrical characteristics stm32f103x8, stm32f103xb 80/105 docid13587 rev 16 figure 40. power supply and reference decoupling (v ref+ connected to v dda ) 1. v ref+ and v ref? inputs are available only on 100-pin packages. 5.3.19 temperature sensor characteristics v ref+ /v dda s tm32f103xx 1 f // 10 nf v ref? /v ss a a i14389 ( s ee note 1) ( s ee note 1) table 50. ts characteristics symbol parameter min typ max unit t l (1) 1. based on characterization, not tested in production. v sense linearity with temperature - ? 1 ? 2 c avg_slope (1) average slope 4.0 4.3 4.6 mv/c v 25 (1) voltage at 25 c 1.34 1.43 1.52 v t start (2) 2. guaranteed by design, not tested in production. startup time 4 - 10 s t s_temp (3)(2) 3. shortest sampling time can be determined in the application by multiple iterations. adc sampling time when reading the temperature - - 17.1 s docid13587 rev 16 81/105 stm32f103x8, stm32f103xb package characteristics 104 6 package characteristics 6.1 package mechanical data in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions a nd product status are available at: www.st.com . ecopack ? is an st trademark. package characteristics stm32f103x8, stm32f103xb 82/105 docid13587 rev 16 1. drawing is not to scale. 2. all leads/pads should also be soldered to th e pcb to improve the lead solder joint life. figure 41. vfqfpn36 6 x 6 mm, 0.5 mm pitch, package outline (1) figure 42. vfqfpn36 recommended footprint (dimensions in mm) (1)(2) s e a ting pl a ne ddd c c a3 a1 a a2 pin # 1 id r = 0.20 zr_me e2 b 19 10 18 27 28 36 19 d2 e d e l 0.30 6.30 0.50 1.00 4.30 4.30 4.80 4.80 4.10 4.10 1 28 9 19 a i14870 b 36 27 18 10 0.75 table 51. vfqfpn36 6 x 6 mm, 0.5 mm pitch, package mechanical data symbol millimeters inches (1) min typ max min typ max a 0.800 0.900 1.000 0.0315 0.0354 0.0394 a1 - 0.020 0.050 - 0.0008 0.0020 a2 - 0.650 1.000 - 0.0256 0.0394 a3 - 0.250 - - 0.0098 - b 0.180 0.230 0.300 0.0071 0.0091 0.0118 d 5.875 6.000 6.125 0.2313 0.2362 0.2411 d2 1.750 3.700 4.250 0.0689 0.1457 0.1673 e 5.875 6.000 6.125 0.2313 0.2362 0.2411 e2 1.750 3.700 4.250 0.0689 0.1457 0.1673 e 0.450 0.500 0.550 0.0177 0.0197 0.0217 l 0.350 0.550 0.750 0.0138 0.0217 0.0295 ddd 0.080 0.0031 1. values in inches are converted from mm and rounded to 4 decimal digits. docid13587 rev 16 83/105 stm32f103x8, stm32f103xb package characteristics 104 figure 43. ufqfpn48 7 x 7 mm, 0.5 mm pitch, package outline 1. drawing is not to scale. 2. there is an exposed die pad on the underside of the qfpn package, this pad is not internally connected to the vss or vdd power pads. it is recommended to connect it to vss. 3. all leads/pads should also be soldered to th e pcb to improve the lead solder joint life. a0b9_me_v3 d pin 1 indentifier laser marking area ee d y d2 e2 exposed pad area z 1 48 detail z r 0.125 typ. 1 48 l c 0.500x45 pin1 corner a seating plane a1 b e ddd detail y t table 52. ufqfpn48 7 x 7 mm, 0.5 mm pitch, package mechanical data symbol millimeters inches (1) min typ max min typ max a 0.500 0.550 0.600 0.0197 0.0217 0.0236 a1 0.000 0.020 0.050 0.0000 0.0008 0.0020 d 6.900 7.000 7.100 0.2717 0.2756 0.2795 e 6.900 7.000 7.100 0.2717 0.2756 0.2795 d2 5.500 5.600 5.700 0.2165 0.2205 0.2244 e2 5.500 5.600 5.700 0.2165 0.2205 0.2244 l 0.300 0.400 0.500 0.0118 0.0157 0.0197 t - 0.152 - - 0.0060 - package characteristics stm32f103x8, stm32f103xb 84/105 docid13587 rev 16 figure 44. ufqfpn48 recommended footprint b 0.200 0.250 0.300 0.0079 0.0098 0.0118 e - 0.500 - - 0.0197 - ddd 0.080 0.0031 1. values in inches are converted from mm and rounded to 4 decimal digits. table 52. ufqfpn48 7 x 7 mm, 0.5 mm pitch, package mechanical data (continued) symbol millimeters inches (1) min typ max min typ max 7.30 7.30 0.20 0.30 0.55 0.50 5.80 6.20 6.20 5.60 5.60 5.80 0.75 a0b9_fp_v2 48 1 12 13 24 25 36 37 docid13587 rev 16 85/105 stm32f103x8, stm32f103xb package characteristics 104 figure 45. lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package outline 1. drawing is not to scale. table 53. lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package mechanical data symbol millimeters inches (1) min typ max min typ max a 1.700 0.0669 a1 0.270 0.0106 a2 0.300 0.0118 a4 0.800 0.0315 b 0.450 0.500 0.550 0.0177 0.0197 0.0217 d 9.850 10.000 10.150 0.3878 0.3937 0.3996 d1 7.200 0.2835 e 9.850 10.000 10.150 0.3878 0.3937 0.3996 e1 7.200 0.2835 e 0.800 0.0315 f 1.400 0.0551 ddd 0.120 0.0047 eee 0.150 0.0059 fff 0.080 0.0031 n (number of balls) 100 h0_me_v2 seating plane a4 a1 e f f d k eee z y x fff ?b (100 balls) ? ? a m m e top view bottom view 1 10 e a a2 z y x z ddd z d1 e1 a1 ball identifier a1 ball index area package characteristics stm32f103x8, stm32f103xb 86/105 docid13587 rev 16 figure 46. recommended pcb design rules (0.80/0.75 mm pitch bga) 1. values in inches are converted from mm and rounded to 4 decimal digits. dpad dsm dpad 0.37 mm dsm 0.52 mm typ. (depends on solder mask registration tolerance solder paste 0.37 mm aperture diameter C non solder mask defined pads are recommended C 4 to 6 mils screen print . 4 7 docid13587 rev 16 87/105 stm32f103x8, stm32f103xb package characteristics 104 figure 47. lqfp100, 14 x 14 mm 100-pin low-profile quad flat package outline (1) figure 48. lqfp100 recommended footprint (1)(2) 1. drawing is not to scale. 2. dimensions are in millimeters. d d1 d3 75 51 50 76 100 26 125 e3 e1 e e b pin 1 identific a tion s eating plane gage plane c a a2 a1 c ccc 0.25 mm 0.10 inch l l1 k c 1l_me 75 51 50 76 0.5 0.3 16.7 14.3 100 26 12.3 25 1.2 16.7 1 a i14906 table 54. lqpf100, 14 x 14 mm 100-pin low-pr ofile quad flat package mechanical data symbol millimeters inches (1) min typ max min typ max a 1.6 0.063 a1 0.05 0.15 0.002 0.0059 a2 1.35 1.4 1.45 0.0531 0.0551 0.0571 b 0.17 0.22 0.27 0.0067 0.0087 0.0106 c 0.09 0.2 0.0035 0.0079 d 15.8 16 16.2 0.622 0.6299 0.6378 d1 13.8 14 14.2 0.5433 0.5512 0.5591 d3 12 0.4724 e 15.8 16 16.2 0.622 0.6299 0.6378 e1 13.8 14 14.2 0.5433 0.5512 0.5591 e3 12 0.4724 e 0.5 0.0197 l 0.45 0.6 0.75 0.0177 0.0236 0.0295 l1 1 0.0394 k 0.0 3.5 7.0 0.0 3.5 7.0 ccc 0.08 0.0031 1. values in inches are converted from mm and rounded to 4 decimal digits. package characteristics stm32f103x8, stm32f103xb 88/105 docid13587 rev 16 figure 49. ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package outline 1. drawing is not to scale. a0c2_me_v2 seating plane a1 e f f d m ?b (100 balls) a e top view bottom view 1 12 a1 ball identifier e a a2 y x z ddd z d1 e1 eee z y x fff ? ? m m z a3 a4 a1 ball index area table 55. ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package mechanical data symbol millimeters inches (1) min typ max min typ max a 0.460 0.530 0.600 0.0181 0.0209 0.0236 a1 0.050 0.080 0.110 0.0020 0.0031 0.0043 a2 0.400 0.450 0.500 0.0157 0.0177 0.0197 a3 0.080 0.130 0.180 0.0031 0.0051 0.0071 a4 0.270 0.320 0.370 0.0106 0.0126 0.0146 b 0.200 0.250 0.300 0. 0079 0.0098 0.0118 d 6.950 7.000 7.050 0.2736 0.2756 0.2776 d1 5.450 5.500 5.550 0.2146 0.2165 0.2185 e 6.950 7.000 7.050 0.2736 0.2756 0.2776 e1 5.450 5.500 5.550 0.2146 0.2165 0.2185 e 0.500 0.0197 f 0.700 0.750 0.800 0.0276 0.0295 0.0315 ddd 0.100 0.0039 eee 0.150 0.0059 fff 0.050 0.0020 1. values in inches are converted from mm and rounded to 4 decimal digits. docid13587 rev 16 89/105 stm32f103x8, stm32f103xb package characteristics 104 figure 50. lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package outline (1) figure 51. lqfp64 recommended footprint (1)(2) 1. drawing is not to scale. 2. dimensions are in millimeters. 5w_me l a1 k l1 d " " ccc $ d d1 d3 e3 e1 e 32 33 48 49 b 64 1 pin 1 identification 16 17 48 32 49 64 17 116 1.2 0.3 33 10.3 12.7 10.3 0.5 7.8 12.7 a i14909 table 56. lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package mechanical data symbol millimeters inches (1) min typ max min typ max a - - 1.60 - - 0.0630 a1 0.05 - 0.15 0.0020 - 0.0059 a2 1.35 1.40 1.45 0.0531 0.0551 0.0571 b 0.17 0.22 0.27 0.0067 0.0087 0.0106 c 0.09 - 0.20 0.0035 - 0.0079 d - 12.00 - - 0.4724 - d1 - 10.00 - - 0.3937 - e - 12.00 - - 0.4724 - e1 - 10.00 - - 0.3937 - e - 0.50 - - 0.0197 - ? 0 3.5 7 0 3.5 7 l 0.45 0.60 0.75 0.0177 0.0236 0.0295 l1 - 1.00 - - 0.0394 - n number of pins 64 1. values in inches are converted from mm and rounded to 4 decimal digits. package characteristics stm32f103x8, stm32f103xb 90/105 docid13587 rev 16 figure 52. tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package outline 1. drawing is not to scale. table 57. tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package mechanical data symbol millimeters inches (1) 1. values in inches are converted from mm and rounded to 4 decimal digits. min typ max min typ max a - - 1.200 - - 0.0472 a1 0.150 - - 0.0059 - - a2 - 0.200 - - 0.0079 - a4 - - 0.600 - - 0.0236 b 0.250 0.300 0.350 0.0098 0.0118 0.0138 d 4.850 5.000 5.150 0.1909 0.1969 0.2028 d1 - 3.500 - - 0.1378 - e 4.850 5.000 5.150 0.1909 0.1969 0.2028 e1 - 3.500 - - 0.1378 - e - 0.500 - - 0.0197 - f - 0.750 - - 0.0295 - ddd - - 0.080 - - 0.0031 eee - - 0.150 - - 0.0059 fff - - 0.050 - - 0.0020 r8_me_v3 seating plane a1 ef f d h ?b (64 balls) a e top view bottom view 1 8 e a y x z ddd z d1 e1 eee z y x fff ? ? m m z a2 a4 a1 ball identifier a1 ball index area docid13587 rev 16 91/105 stm32f103x8, stm32f103xb package characteristics 104 figure 53. recommended pcb design rules for pads (0.5 mm pitch bga) 1. non solder mask defined (nsmd) pads are recommended 2. 4 to 6 mils solder paste screen printing process pitch 0.5 mm d p a d 0.27 mm d s m 0.35 mm typ (depend s on the s olderm as k regi s tr a tion toler a nce) s older p as te 0.27 mm a pert u re di a meter dp a d d s m a i15495 package characteristics stm32f103x8, stm32f103xb 92/105 docid13587 rev 16 figure 54. lqfp48, 7 x 7 mm, 48-pin low-profile quad flat package outline (1) figure 55. lqfp48 recommended footprint (1)(2) 1. drawing is not to scale. 2. dimensions are in millimeters. d d1 d3 a1 l1 l k c b ccc c a1 a2 a c s e a ting pl a ne 0.25 mm g a ge pl a ne e3 e1 e 12 13 24 25 48 1 36 37 pin 1 identific a tion 5b_me 9.70 5.80 7.30 12 24 0.20 7.30 1 37 36 1.20 5.80 9.70 0.30 25 1.20 0.50 13 48 table 58. lqfp48, 7 x 7 mm, 48-pin low-profile quad flat package mechanical data symbol millimeters inches (1) min typ max min typ max a - - 1.600 - - 0.0630 a1 0.050 - 0.150 0.0020 - 0.0059 a2 1.350 1.400 1.450 0.0531 0.0551 0.0571 b 0.170 0.220 0.270 0.0067 0.0087 0.0106 c 0.090 - 0.200 0.0035 - 0.0079 d 8.800 9.000 9.200 0.3465 0.3543 0.3622 d1 6.800 7.000 7.200 0.2677 0.2756 0.2835 d3 - 5.500 - - 0.2165 - e 8.800 9.000 9.200 0.3465 0.3543 0.3622 e1 6.800 7.000 7.200 0.2677 0.2756 0.2835 e3 - 5.500 - - 0.2165 - e - 0.500 - - 0.0197 - l 0.450 0.600 0.750 0.0177 0.0236 0.0295 l1 - 1.000 - - 0.0394 - k 03.57 03.57 ccc 0.080 0.0031 1. values in inches are converted from mm and rounded to 4 decimal digits. docid13587 rev 16 93/105 stm32f103x8, stm32f103xb package characteristics 104 6.2 thermal characteristics the maximum chip junction temperature (t j max) must never exceed the values given in table 9: general operating conditions on page 38 . the maximum chip-junction temperature, t j max, in degrees celsius, may be calculated using the following equation: t j max = t a max + (p d max ? ja ) where: ? t a max is the maximum ambient temperature in ? c, ?? ja is the package junction-to-ambient thermal resistance, in ? c/w, ? p d max is the sum of p int max and p i/o max (p d max = p int max + p i/o max), ? p int max is the product of i dd and v dd , expressed in watts. th is is the maximum chip internal power. p i/o max represents the maximum power dissipation on output pins where: p i/o max = ?? (v ol i ol ) + ? ((v dd ? v oh ) i oh ), taking into account the actual v ol / i ol and v oh / i oh of the i/os at low and high level in the application. 6.2.1 reference document jesd51-2 integrated circuits thermal test method environment conditions - natural convection (still air). available from www.jedec.org. table 59. package thermal characteristics symbol parameter value unit ? ja thermal resistance junction-ambient lfbga100 - 10 10 mm / 0.8 mm pitch 44 c/w thermal resistance junction-ambient lqfp100 - 14 14 mm / 0.5 mm pitch 46 thermal resistance junction-ambient ufbga100 - 7 7 mm /0.5 mm pitch 59 thermal resistance junction-ambient lqfp64 - 10 10 mm / 0.5 mm pitch 45 thermal resistance junction-ambient tfbga64 - 5 5 mm / 0.5 mm pitch 65 thermal resistance junction-ambient lqfp48 - 7 x 7 mm / 0.5 mm pitch 55 thermal resistance junction-ambient ufqfpn 48 - 7 7 mm / 0.5 mm pitch 32 thermal resistance junction-ambient vfqfpn 36 - 6 6 mm / 0.5 mm pitch 18 package characteristics stm32f103x8, stm32f103xb 94/105 docid13587 rev 16 6.2.2 selecting the product temperature range when ordering the microcontroller, the temperature range is specified in the ordering information scheme shown in table 60: ordering information scheme . each temperature range suffix corresponds to a specific guaranteed ambient temperature at maximum dissipation and, to a spec ific maximum junction temperature. as applications do not commonly use the stm32f 103xx at maximum dissipation, it is useful to calculate the exact power consumption and junction temperature to determine which temperature ra nge will be best suited to the application. the following examples show how to calculat e the temperature range needed for a given application. example 1: high-performance application assuming the following ap plication conditions: maximum ambient temperature t amax = 82 c (measured according to jesd51-2), i ddmax = 50 ma, v dd = 3.5 v, maximum 20 i/os used at the same time in output at low level with i ol = 8 ma, v ol = 0.4 v and maximum 8 i/os used at the same time in output at low level with i ol = 20 ma, v ol = 1.3 v p intmax = 50 ma 3.5 v= 175 mw p iomax = 20 8 ma 0.4 v + 8 20 ma 1.3 v = 272 mw this gives: p intmax = 175 mw and p iomax = 272 mw: p dmax = 175 + 272 = 447 mw thus: p dmax = 447 mw using the values obtained in table 59 t jmax is calculated as follows: ? for lqfp100, 46 c/w t jmax = 82 c + (46 c/w 447 mw) = 82 c + 20.6 c = 102.6 c this is within the range of the suffix 6 version parts (?40 < t j < 105 c). in this case, parts must be ordered at leas t with the temperature range suffix 6 (see table 60: ordering information scheme ). example 2: high-temperature application using the same rules, it is possible to address applications that run at high ambient temperatures with a low dissipation, as long as junction temperature t j remains within the specified range. assuming the following ap plication conditions: maximum ambient temperature t amax = 115 c (measured according to jesd51-2), i ddmax = 20 ma, v dd = 3.5 v, maximum 20 i/os used at the same time in output at low level with i ol = 8 ma, v ol = 0.4 v p intmax = 20 ma 3.5 v= 70 mw p iomax = 20 8 ma 0.4 v = 64 mw this gives: p intmax = 70 mw and p iomax = 64 mw: p dmax = 70 + 64 = 134 mw thus: p dmax = 134 mw docid13587 rev 16 95/105 stm32f103x8, stm32f103xb package characteristics 104 using the values obtained in table 59 t jmax is calculated as follows: ? for lqfp100, 46 c/w t jmax = 115 c + (46 c/w 134 mw) = 115 c + 6.2 c = 121.2 c this is within the range of the suffix 7 version parts (?40 < t j < 125 c). in this case, parts must be ordered at leas t with the temperature range suffix 7 (see table 60: ordering information scheme ). figure 56. lqfp100 p d max vs. t a 0 100 200 300 400 500 600 700 65 75 85 95 105 115 125 135 t a (c) p d (mw) su ffix 6 su ffix 7 ordering information scheme stm32f103x8, stm32f103xb 96/105 docid13587 rev 16 7 ordering information scheme for a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest st sales office. table 60. ordering information scheme example: stm32 f 103 c 8 t 7 xxx device family stm32 = arm-based 32-bit microcontroller product type f = general-purpose device subfamily 103 = performance line pin count t = 36 pins c = 48 pins r = 64 pins v = 100 pins flash memory size (1) 1. although stm32f103x6 devices are not described in this datasheet, orderable part numbers that do not show the a internal code after temperature range c ode 6 or 7 should be referred to this datasheet for the electrical characteristic s. the low-density datasheet only covers stm32f103x6 devices that feature the a code. 8 = 64 kbytes of flash memory b = 128 kbytes of flash memory package h = bga i = ufbga t = lqfp u = vfqfpn or ufqfpn temperature range 6 = industrial temperature range, ?40 to 85 c. 7 = industrial temperature range, ?40 to 105 c. options xxx = programmed parts tr = tape and real docid13587 rev 16 97/105 stm32f103x8, stm32f103xb revision history 104 8 revision history table 61. document revision history date revision changes 01-jun-2007 1 initial release. 20-jul-2007 2 flash memory size modified in note 9 , note 5 , note 7 , note 7 and bga100 pins added to table 5: medium-density stm32f103xx pin definitions . figure 3: stm32f103xx performance line lfbga100 ballout added. t hse changed to t lse in figure 23: low-speed external clock source ac timing diagram . v bat ranged modified in power supply schemes . t su(lse) changed to t su(hse) in table 22: hse 4-16 mhz oscillator characteristics . i dd(hsi) max value added to table 24: hsi oscillator characteristics . sample size modified and machine model removed in electrostatic discharge (esd) . number of parts modified and standard reference updated in static latch-up . 25 c and 85 c conditions removed and class name modified in table 33: electrical sensitivities . r pu and r pd min and max values added to table 35: i/o static characteristics . r pu min and max values added to table 38: nrst pin characteristics . figure 32: i2c bus ac waveforms and measurement circuit and figure 31: recommended nrst pin protection corrected. notes removed below ta ble 9 , ta ble 38 , table 44 . i dd typical values changed in table 11: maximum current consumption in run and sleep modes . table 39: timx characteristics modified. t stab , v ref+ value, t lat and f trig added to table 46: adc characteristics . in table 29: flash memory endurance and data retention , typical endurance and data retention for t a = 85 c added, data retention for t a = 25 c removed. v bg changed to v refint in table 12: embedded internal reference voltage . document title changed. controller area network (can) section modified. figure 14: power supply scheme modified. features on page 1 list optimized. small text changes. revision history stm32f103x8, stm32f103xb 98/105 docid13587 rev 16 18-oct-2007 3 stm32f103cbt6, stm32f103t6 and stm32f103t8 root part numbers added (see table 2: stm32f103xx me dium-density device features and peripheral counts ) vfqfpn36 package added (see section 6: package characteristics ). all packages are ecopack? compliant. package mechanical data inch values are calculated from mm and rounded to 4 decimal digits (see section 6: package characteristics ). table 5: medium-density stm32f103xx pin definitions updated and clarified. table 26: low-power mode wakeup timings updated. t a min corrected in table 12: embedded internal reference voltage . note 2 added below table 22: hse 4-16 mhz oscillator characteristics . v esd(cdm) value added to table 32: esd absolute maximum ratings . note 4 added and v oh parameter description modified in table 36: output voltage characteristics . note 1 modified under table 37: i/o ac characteristics . equation 1 and table 47: rain max for fadc = 14 mhz added to section 5.3.18: 12-bit adc characteristics . v ain , t s max, t conv , v ref+ min and t lat max modified, notes modified and t latr added in table 46: adc characteristics . figure 37: adc accuracy characteristics updated. note 1 modified below figure 38: typical connection diagram using the adc . electrostatic discharge (esd) on page 60 modified. number of tim4 channels modified in figure 1: stm32f103xx performance line block diagram . maximum current consumption table 13 , table 14 and table 15 updated. v hys modified in table 35: i/o static characteristics . table 49: adc accuracy updated. t vdd modified in table 10: operating conditions at power-up / power-down . v fesd value added in table 30: ems characteristics . values corrected, note 2 modified and note 3 removed in table 26: low- power mode wakeup timings . table 16: typical and maximum current consumptions in stop and standby modes : typical values added for v dd /v bat = 2.4 v, note 2 modified, note 2 added. table 21: typical current consumption in standby mode added. on-chip peripheral current consumption on page 50 added. acc hsi values updated in table 24: hsi oscillator characteristics . v prog added to table 28: flash memory characteristics . upper option byte address modified in figure 11: memory map . typical f lsi value added in table 25: lsi oscillator characteristics and internal rc value corrected from 32 to 40 khz in entire document. t s_temp added to table 50: ts characteristics . n end modified in table 29: flash memory endurance and data retention . t s_vrefint added to table 12: embedded internal reference voltage . handling of unused pins specified in general input/output characteristics on page 62 . all i/os are cmos and ttl compliant. figure 39: power supply and reference decoupling (vref+ not connected to vdda) modified. t jitter and f vco removed from table 27: pll characteristics . appendix a: important notes on page 81 added. added figure 16 , figure 17 , figure 19 and figure 21 . table 61. document revi sion history (continued) date revision changes docid13587 rev 16 99/105 stm32f103x8, stm32f103xb revision history 104 22-nov-2007 4 document status promoted from preliminary data to datasheet. the stm32f103xx is usb certified. small text changes. power supply schemes on page 15 modified. number of communication peripherals corrected for stm32f103tx and number of gpios corrected for lqfp package in table 2: stm32f103 xx medium-density device features and peripheral counts . main function and default alternate function modified for pc14 and pc15 in, note 6 added and remap column added in table 5: medium-density stm32f103xx pin definitions . v dd ?v ss ratings and note 1 modified in table 6: voltage characteristics , note 1 modified in table 7: current characteristics . note 1 and note 2 added in table 11: embedded reset and power control block characteristics . i dd value at 72 mhz with peripherals enabled modified in ta ble 14 : maximum current consumption in run mode, code with data processing running from ram . i dd value at 72 mhz with peripherals enabled modified in ta ble 15 : maximum current consumption in slee p mode, code running from flash or ram on page 44 . i dd_vbat typical value at 2.4 v modified and i dd_vbat maximum values added in table 16: typical and maximum current consumptions in stop and standby modes . note added in table 17 on page 48 and table 18 on page 49 . adc1 and adc2 consumption and notes modified in table 19: peripheral current consumption . t su(hse) and t su(lse) conditions modified in table 22 and ta ble 23 , respectively. maximum values removed from table 26: low-power mode wakeup timings . t ret conditions modified in table 29: flash memory endurance and data retention . figure 14: power supply scheme corrected. figure 20: typical current consumption in stop mode with regulator in low-power mode versus temperat ure at vdd = 3.3 v and 3.6 v added. note removed below figure 33: spi timing diagram - slave mode and cpha = 0 . note added below figure 34: spi timing diagram - slave mode and cpha = 1(1) . details on unused pins removed from general input/output characteristics on page 62 . table 42: spi characteristics updated. table 43: usb startup time added. v ain , t lat and t latr modified, note added and i lkg removed in table 46: adc characteristics . test conditions modified and note added in table 49: adc accuracy . note added below table 47 and ta ble 50 . inch values corrected in table 54: lqpf100, 14 x 14 mm 100-pin low- profile quad flat package mechanical data , table 56: lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package mechanical data and table 58: lqfp48, 7 x 7 mm, 48-pin low-profile quad flat package mechanical data . ? ja value for vfqfpn36 package added in table 59: package thermal characteristics ? order codes replaced by section 7: ordering information scheme . mcu ?s operating conditions modified in typical current consumption on page 47 . avg_slope and v 25 modified in table 50: ts characteristics . i2c interface characteristics on page 70 modified. impedance size specified in a.4: voltage glitch on adc input 0 on page 81 . table 61. document revi sion history (continued) date revision changes revision history stm32f103x8, stm32f103xb 100/105 docid13587 rev 16 14-mar-2008 5 figure 2: clock tree on page 12 added. maximum t j value given in table 8: thermal characteristics on page 38 . crc feature added (see crc (cyclic redundancy check) calculation unit on page 9 and figure 11: memory map on page 34 for address). i dd modified in table 16: typical and maximum current consumptions in stop and standby modes . acc hsi modified in table 24: hsi oscillator characteristics on page 55 , note 2 removed. p d , t a and t j added, t prog values modified and t prog description clarified in table 28: flash memory characteristics on page 57 . t ret modified in table 29: flash memory endurance and data retention . v nf(nrst) unit corrected in table 38: nrst pin characteristics on page 68 . table 42: spi characteristics on page 72 modified. i vref added to table 46: adc characteristics on page 76 . table 48: adc accuracy - limited test conditions added. table 49: adc accuracy modified. lqfp100 package specifications updated (see section 6: package characteristics on page 81 ). recommended lqfp100, lqfp 64, lq fp48 and vfqfpn36 footprints added (see figure 48 , figure 51 , figure 55 and figure 42 ). section 6.2: thermal characteristics on page 93 modified, section 6.2.1 and section 6.2.2 added. appendix a: important notes on page 81 removed. 21-mar-2008 6 small text changes. figure 11: memory map clarified. in table 29: flash memory endurance and data retention : ?n end tested over the whole temperature range ? cycling conditions specified for t ret ?t ret min modified at t a = 55 c v 25 , avg_slope and t l modified in table 50: ts characteristics . crc feature removed. 22-may-2008 7 crc feature added back. small text changes. section 1: introduction modified. section 2.2: full compatibility throughout the family added. i dd at t a max = 105 c added to table 16: typical and maximum current consumptions in stop and standby modes on page 45 . i dd_vbat removed from table 21: typical current consumption in standby mode on page 47 . values added to table 41: scl frequency (fpclk1= 36 mhz.,vdd_i2c = 3.3 v) on page 71 . figure 33: spi timing diagram - slave mode and cpha = 0 on page 73 modified. equation 1 corrected. t ret at t a = 105 c modified in table 29: flash memory endurance and data retention on page 58 . v usb added to table 44: usb dc electrical characteristics on page 75 . figure 56: lqfp100 pd max vs. ta on page 95 modified. axx option added to table 60: ordering information scheme on page 96 . table 61. document revi sion history (continued) date revision changes docid13587 rev 16 101/105 stm32f103x8, stm32f103xb revision history 104 21-jul-2008 8 power supply supervisor updated and v dda added to table 9: general operating conditions . capacitance modified in figure 14: power supply scheme on page 36 . table notes revised in section 5: electrical characteristics . table 16: typical and maximum current consumptions in stop and standby modes modified. data added to table 16: typical and maximum current consumptions in stop and standby modes and table 21: typical current consumption in standby mode removed. f hse_ext modified in table 20: high-speed external user clock characteristics on page 51 . f pll_in modified in table 27: pll characteristics on page 57 . minimum sda and scl fall time val ue for fast mode removed from table 40: i2c characteristics on page 70 , note 1 modified. t h(nss) modified in table 42: spi characteristics on page 72 and figure 33: spi timing diagram - slave mode and cpha = 0 on page 73 . c adc modified in table 46: adc characteristics on page 76 and figure 38: typical connection diagram using the adc modified. typical t s_temp value removed from table 50: ts characteristics on page 80 . lqfp48 package specifications updated (see table 58 and ta ble 55 ), section 6: package characteristics revised. axx option removed from table 60: ordering information scheme on page 96 . small text changes. 22-sep-2008 9 stm32f103x6 part numbers removed (see table 60: ordering information scheme ). small text changes. general-purpose timers (timx) and advanced-control ti mer (tim1) on page 18 updated. notes updated in table 5: medium-density stm32f103xx pin definitions on page 28 . note 2 modified below table 6: voltage characteristics on page 37 , | ? v ddx | min and | ? v ddx | min removed. measurement conditions specified in section 5.3.5: supply current characteristics on page 41 . i dd in standby mode at 85 c modified in table 16: typical and maximum current consumptions in stop and standby modes on page 45 . general input/output characteristics on page 62 modified. f hclk conditions modified in table 30: ems characteristics on page 59 . ? ja and pitch value modified for lfbga100 package in table 59: package thermal characteristics . small text changes. table 61. document revi sion history (continued) date revision changes revision history stm32f103x8, stm32f103xb 102/105 docid13587 rev 16 23-apr-2009 10 i/o information clarified on page 1 . figure 3: stm32f103xx performance line lfbga100 ballout modified. figure 11: memory map modified. table 4: timer feature comparison added. pb4, pb13, pb14, pb15, pb3/tracesw o moved from default column to remap column in table 5: medium-density stm32f103xx pin definitions . p d for lfbga100 corrected in table 9: general operating conditions . note modified in table 13: maximum current consumption in run mode, code with data processing running from flash and table 15: maximum current consumption in sleep mode, code running from flash or ram . table 20: high-speed external user clock characteristics and table 21: low-speed external user clock characteristics modified. figure 20 shows a typical curve (title modified). acc hsi max values modified in table 24: hsi oscillator characteristics . tfbga64 package added (see table 57 and table 52 ). small text changes. 22-sep-2009 11 note 5 updated and note 4 added in table 5: medium-density stm32f103xx pin definitions . v rerint and t coeff added to table 12: embedded internal reference voltage . i dd_vbat value added to table 16: typical and maximum current consumptions in stop and standby modes . figure 18: typical current consumption on vbat with rtc on versus temperature at different vbat values added. f hse_ext min modified in table 20: high-speed external user clock characteristics . c l1 and c l2 replaced by c in table 22: hse 4-16 mhz oscillator characteristics and table 23: lse oscillator characteristics (flse = 32.768 khz) , notes modified and moved below the tables. table 24: hsi oscillator characteristics modified. conditions removed from table 26: low-power mode wakeup timings . note 1 modified below figure 24: typical application with an 8 mhz crystal . iec 1000 standard updat ed to iec 61000 and sae j1752/3 u pdated to iec 61967-2 in section 5.3.10: emc characteristics on page 58 . jitter added to table 27: pll characteristics . table 42: spi characteristics modified. c adc and r ain parameters modified in table 46: adc characteristics . r ain max values modified in table 47: rain max for fadc = 14 mhz . figure 45: lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package outline updated. 03-jun-2010 12 added stm32f103tb devices. added vfqfpn48 package. updated note 2 below table 40: i2c characteristics updated figure 32: i2c bus ac waveforms and measurement circuit updated figure 31: recommended nrst pin protection updated section 5.3.12: i/o current injection characteristics table 61. document revi sion history (continued) date revision changes docid13587 rev 16 103/105 stm32f103x8, stm32f103xb revision history 104 19-apr-2011 13 updated footnotes below table 6: voltage characteristics on page 37 and table 7: current characteristics on page 38 updated tw min in table 20: high-speed external user clock characteristics on page 51 updated startup time in table 23: lse oscillator characteristics (flse = 32.768 khz) on page 54 added section 5.3.12: i/o current injection characteristics updated section 5.3.13: i/o port characteristics 07-dec-2012 14 added ufbga100 7 x 7 mm. updated figure 50: lqfp64, 10 x 10 mm, 64-pin low-profile quad flat package outline to add pin 1 identification. table 61. document revi sion history (continued) date revision changes revision history stm32f103x8, stm32f103xb 104/105 docid13587 rev 16 14-may-2013 15 replaced vqfn48 package with uqfn48 in cover page packages, table 2: stm32f103xx medium-density device features and peripheral counts , figure 9: stm32f103xx performance line ufqfpn48 pinout , table 2: stm32f103xx medium-density device features and peripheral counts , table 55: ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package mechanical data , table 60: ordering information scheme and updated table 59: package thermal characteristics added footnote for tfbga adc channels in table 2: stm32f103xx medium-density device features and peripheral counts updated ?all gpios are high current...? in section 2.3.21: gpios (general-purpose inputs/outputs) updated table 5: medium-density stm32f103xx pin definitions corrected sigma letter in section 5.1.1: minimu m and maximum values removed the first sentence in section 5.3.16: communications interfaces added ?v in ? in table 9: general operating conditions updated first sentence in output driving current added note 5. in table 24: hsi oscillator characteristics updated ?v il ? and ?v ih ? in table 35: i/o static characteristics added notes to figure 26: standard i/o input characteristics - cmos port , figure 27: standard i/o input characteristics - ttl port , figure 28: 5 v tolerant i/o input characteristics - cmos port and figure 29: 5 v tolerant i/o input characteristics - ttl port updated figure 32: i2c bus ac waveforms and measurement circuit updated note 2. and 3. ,removed note ?the device must internally...? in table 40: i2c characteristics updated title of table 41: scl frequency (fpclk1= 36 mhz.,vdd_i2c = 3.3 v) updated note 2. in table 49: adc accuracy updated figure 49: ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package outline and table 55: ufbga100 - ultra fine pitch ball grid array, 7 x 7 mm, 0.50 mm pitch, package mechanical data updated figure 45: lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package outline and table 53: lfbga100 - 10 x 10 mm low profile fine pitch ball grid array package mechanical data updated figure 52: tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package outline and table 57: tfbga64 - 8 x 8 active ball array, 5 x 5 mm, 0.5 mm pitch, package mechanical data 05-aug-2013 16 updated the reference for ?v esd(cdm) ? in table 32: esd absolute maximum ratings corrected ?tf(io)out? in figure 30: i/o ac characteristics definition updated table 52: ufqfpn48 7 x 7 mm, 0.5 mm pitch, package mechanical data table 61. document revi sion history (continued) date revision changes docid13587 rev 16 105/105 stm32f103x8, stm32f103xb 105 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not authorized for use in weapons. nor are st products designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com |
Price & Availability of STM32F103B
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |